Jump to content
SAU Community

Purchacing A Skyline

nicksrex
 Share

Recommended Posts

skylineboy84 Apprentice

skylineboy84

Posted
Posted

if its got less than 100,000k on the clock have a look at the moto to see if its got a 100,000k service sticker, if its got the sticker pretty much means the clock been put back, for alot of r32,r33 gtst this is the case, i went to one import shop and they had 4 r33 that were like this, one had a 190,000k service sticker on it and the clock said 85,000. :cool:

GTR-N1 Grand Master

GTR-N1

Posted
Posted
Hey, im looking at purchacing a skyline and wanted to know what are some common problems to look out for and whats the best workshop to get a car looked at before i buy it? Thanks for your help

Hi Nick,

Certain idiosyncrasies exist (besides being vigilant for rust, any damage that hasn't been repaired properly, service history etc) whether it's an R32, R33 or R34. Which one?

To better answer your 2nd Q, just wondering what city u r in? Your Profile says 'Location Unknown'.

Regards, T

nicksrex Rookie

nicksrex

Posted
  • Author
Posted
Hi Nick,

Certain idiosyncrasies exist (besides being vigilant for rust, any damage that hasn't been repaired properly, service history etc) whether it's an R32, R33 or R34. Which one?

To better answer your 2nd Q, just wondering what city u r in? Your Profile says 'Location Unknown'.

Regards, T

im looking at a r33 gtst and im in perth.

the post previously said about a sticker saying th kms just wondering where that sticker is usually put? its not the service sticker is it?

GTR-N1 Grand Master

GTR-N1

Posted
Posted

Hi Nick,

I believe that Quinny is cautioning you about a sticker on the block or thereabouts that would confirm that the timing belt has been changed &/or other things.

The previous owner if in Oz should have the Kms travelled according to the odometer at the rego inspection certicate to act as a progress marker.

Wear and tear on the bolsters and carpet + sun damage to the steering wheel are also markers.

If the car has been in Japan all this time, extra care has to be taken looking for rust in the undercarriage as well as hinges, body panels, around window seals because Japan has acid rain in Honshu as well as parts of Kyushu Islands combined with salt. But even in Perth, if you live anywhere near the sea, you'll get salt from the Fremantle Dr. Rust on Skylines ain't as bad as Alfas before the 90s but your investment is worth checking over. Look at the owner's body language as you ask him if he'll let you put the car up on a hoist.

On inspection, take >1 mechanic with you (to go through your pre-planned checklist) as you check for rust, oil leaks/seepage, sludge under/around the oil-fill opening, previous damage & bad repairs, air cond, electric windows, heater, windscreen chips, unevenly worn tyres, lights. If you detect damage, ask for his insurance company on that car so that a check can be done (on claims) with his permission. Also check for scratched paint on the corners of panel bolts around the engine.

Personally, I can't think of many things to specifically look for on a R33 GTsT, but hey, you'll pick up 100s of messages through the seat and steering wheel after you then start the engine.

Happy Searching!

T

OzCarImports Collaborator

OzCarImports

Posted
Posted (edited)
if its got less than 100,000k on the clock have a look at the moto to see if its got a 100,000k service sticker, if its got the sticker pretty much means the clock been put back, for alot of r32,r33 gtst this is the case, i went to one import shop and they had 4 r33 that were like this, one had a 190,000k service sticker on it and the clock said 85,000. :cool:

JEVIC!

Check this link out, be better if more imports had this inspection, save alot of head aches for people before they lay there hard earned cash out on the table.

I have all my car inspected before they leave Japan.

http://www.jevic.co.jp/jevic_english/inspe...ces/index4.html

Edited by OzCarImports
skylineboy84 Apprentice

skylineboy84

Posted
Posted

Yup thats it when the timing belt was change

im looking at a r33 gtst and im in perth.

the post previously said about a sticker saying th kms just wondering where that sticker is usually put? its not the service sticker is it?

post-47818-1217657766_thumb.jpg

G0DZLR Mentor

G0DZLR

Posted
Posted
Yup thats it when the timing belt was change

will the sticker have something written on it to indicate its been changed? or have to have something to be marked off? cos mine has it, but my odo is only at 88xxxkms

nicksrex Rookie

nicksrex

Posted
  • Author
Posted
yup! could it be my belts were changed before the 100,000k service, or has my odo been wound back...

I was under the impression the sticker was there to remind you to get the timing belt changed at 100k and then when its done its ither replaced with a new sticker or they write on the existing sticker what kms the belt was changed. Wheres the best workshop to get the car checked? And roughly how much is it?

GTR-N1 Grand Master

GTR-N1

Posted
Posted
yup! could it be my belts were changed before the 100,000k service, or has my odo been wound back...

Just as Quinny above has said, it looks as if the odo has been wound back if

i) the sticker says that the timing belt has been changed already and

ii) you're the 1st Australian owner or

But then again, perhaps the oil pump's been changed!

It's recommended to change the timing belt if the oil pump has had it.

But if you're the >2nd Aussie owner, it may be that the previous owner changed it anyway through caution or the oil pump's been changed

Granthem Mentor

Granthem

Posted
Posted

The 100,000.00 service would be a KM or date service correct? Like most cars its whatever comes first. I know my GFs civic has had one of its major services (i think 50k service) and its barely cracked 30. Just the way it goes if you wanna keep your warranty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...