Jump to content
SAU Community

R33 S1 Bitz & After Market Parts

RBJ3T
 Share

Recommended Posts

RBJ3T Proficient

RBJ3T

Posted
Posted

I have done a bit of a work on the car and thought if anyone wants any of the stock parts they are more than welcome. ALl these parts have only done 90,000 kms.

I have:

Rotors and Pads. In good nick $100

Suspension: $100 boots are a bit worse for ware but the suspension is A OK.

Turbo Smart BOV with connector. $50

Engel Eye lights (mock up multi colour little lights for the front bar. $30

I'll give whoever wants the lot for $200.

PM me for more details.

I'm in the S.E Burbs of Melbourne.

Link to comment
https://www.sau.com.au/forums/topic/230845-r33-s1-bitz-after-market-parts/
Share on other sites
RBJ3T Proficient

RBJ3T

Posted
  • Author
Posted

Don't let the pics fool you guys. If your looking for a pretty shiny BOV your looking for it for the wrong reasons. You should be hiding it away from Mr Plod anyway. Don't let the looks fool you this baby is freaking load & full adjustable.

Anyway if you want it let me know. Good luck finding another for $50.

Russcoe Apprentice

Russcoe

Posted
Posted
I have done a bit of a work on the car and thought if anyone wants any of the stock parts they are more than welcome. ALl these parts have only done 90,000 kms.

I have:

Rotors and Pads. In good nick $100

Suspension: $100 boots are a bit worse for ware but the suspension is A OK.

Turbo Smart BOV with connector. $50

Engel Eye lights (mock up multi colour little lights for the front bar. $30

I'll give whoever wants the lot for $200.

PM me for more details.

I'm in the S.E Burbs of Melbourne.

If you still have standard suspension, email pics to [email protected], cash buyer no mucking around.

vintek Newbie

vintek

Posted
Posted
If you still have standard suspension, email pics to [email protected], cash buyer no mucking around.

im interested in suspension, is that full shockers and springs.

email [email protected] if you still have and ill come pick them up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...