Jump to content
SAU Community

Defected Again...... And A $493 Fine!!!!


Recommended Posts

Yeah cos its a country area i'm worried if i make a complaint that i will get arse fuct, and they will hammer me everytime they see me.

Just sucks, well i can't wait till i move to adelaide at the end of the year.... Alot less chance of me gettin picked on and done up there plus me gonna b changin me plates hehe.

About the height i think i may put it up to or a smidge below standard ay........

Or i think i may just sell my car and get a GTi-R cos i'm sick of this shit ay!

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by MADGT4

Yeah cos its a country area i'm worried if i make a complaint that i will get arse fuct, and they will hammer me everytime they see me.

I understand, but if you make sure that you keep record of all instances that you have contact and what was said (I know this sounds a bit over the top, but carry a tape recorder, or even better a video camera:D) and if they step out of line go directly to their supervisor. I think the days where coppers can get away with shit are dwindling - they have to be fully accountable for their actions, no more coverups especially if you have evidence.

It is a tough choice, but personally I wouldnt put up with crap on principle. No reason if you arent doing anything wrong that you should be getting hasselled.

Hippy, legal lowering height is 350mm from middle of wheel hub to the top of the guard, also no part of the car should be lower than 100mm with (cant rember how many) metres of the axles(applies to larger vehicles) - but it basically means you cant get lower than 100mm. And the car must sit on the rims if the tyre deflates;) Thats from memory anyways.

Dont worry about the dump hippy, its sitting waiting for you:)

I've been lucky so far - have never been pulled over!! Fingers crossed, but I guess it'll happen one day ;)

My b/f's bro got pulled over and defected in a stock N13 pulsar the other night for being too low. The cop's parting comment was " You're just lucky you don't have an import mate" - now whats with that?! :confused:

Did they put all 3 defects on the 1 defect slip? If so then you only need to pay 1 fine (atleast in nsw).

If they wrote 3 different defect slips for each fault then you'll be up for 3x the $$$

Also how did they come to the conclusion that your exhaust was "too loud" ? Did they test your exhaust with a small device standing behind your exhaust as you hold the revs at 3000rpm? If they just pulled you over and said "your exhaust sounds too loud here's a defect" report them to the local cop shop.

The reason they knew it was too low, too loud blah blah is cause when i passed my defect i put everything back on there and he goes to me "we know you put everything back on the after u passed"

"your just mocking the system" he recons which is why i copped the fine.

mechanically my car is A1 but no all the ****in bush bunnie fuct up shit boxes are allowed 2 drive round here and stuff but i can't drive my car round!

Plus when i tell ppl that my car had been defected again they say "why its allways so neat and looked after"

my reply?

"Revenue Raising Traffic Nazi's With Nothing Else Better To Do"

Originally posted by CheekyR32

What about when its chick cops (with bigger balls than most of you boys) that pull you over???  

Then your powers are void...

Actually, when the chick coppers have a big set of hairy dusters, your powers are just as relevant as ever, if not more :)

my friend got his 180 defected .. just for a bov ... went to regency ... they then gave him half a page of stuff to fix ... double defected ... now he's probably going to have to spend maybe 500-1k just to pass ... they just out to screw u over ... whoever died from a bov anyway?

Hippy some bov are pretty big, perhaps you could hit someone with it hard enough you could kill them.

Beside that, they are very useful.

You could use them for pest control - throw them at rats and larger ****roaches, mormons etc.

You could put it on the coffee table, after a good cleanup, and use it as a conversation peice. Be very handy if you had unwelcome visitors.

You could even use it to chock your wheels if you have to change a flat, but it would be better to use a brick.

It would also make a good paper weight.

Perhaps you could even use it to stop air reverting through the compressor of a turbo and causing damage. Nah sorry, just being plain silly now.

By the way, anybody want to buy a bov? I have a spare one - shiney and red....hmmm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...