Jump to content
SAU Community

Recommended Posts

nice build, cant wait to see results :thumbsup:

i also run the npc twin plate and its the best clutch for the power it handles, i've drivin extreme single plates, os giken twin and quad plates and direct clutches and they are all nothing compared to the smoothness and nice soft pedal feel of the NPC. Ive done tonnes of launches with 420kw+ (In 4wd) and never had an issue with slipping either :D

  • 2 months later...
  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

post-27445-1235737124_thumb.jpg

It took awhile but she's finally tuned. Set to 21psi for the mean time as this is the minimum boost we can get it down too.Torque is over 2000ft/lbs. I will eventually run up to 24+psi if pump fuel/gearbox allows. Right now im "TRYING" to handle the power as best as i can. All i can say is god dam fark!!!! Its insane! The most atm is 1/2 throttle in third gear. Absolutely no traction at all. As soon as the gate cracks it just smokes the tyres but hell is fun to drive. VERY dangerous and unpredictable. Cheers to all the boys at topracing. Did a great job and i will highly recommend them.

That would be tractive effort, not torque.

"The tractive effort is obtained by multiplying the torque by the total ratio of power train and dividing this sum by the rolling radius of the driving tyres."

Show us a torque graph, and we can tell you approximately the 'real world' torque values.

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...