Jump to content
SAU Community

Exhaust Install


jko_one
 Share

Recommended Posts

I just purchased a cat back exhaust and want to install it myself

it looks simple, just slip the old one out of the rubber mounts and put the new one in

is that it or is there a trick to it?

I just dont want to break it (with a hammer when it pisses me off) :P

Link to comment
Share on other sites

well - how easy the job will be depends greatly on the quality of the catback you bought.

if it was on a stock standard stagea before you will probably be fine!

the only thing that might stuff you up is the orientation / roation of the flange that bolts onto the cat. Hopefully all the hangers are in place. Some of those exhaust bolts can be pretty tight to remove!

good luck matey!

Link to comment
Share on other sites

spray WD40 (or similar) onto the bolts while the exhaust is still hot, it will help loosen the bolts. dont be shy with it, it will smell and fizzle, but it saves you a few skinned knuckles, its well worth it :starwars:

Link to comment
Share on other sites

well - how easy the job will be depends greatly on the quality of the catback you bought.

if it was on a stock standard stagea before you will probably be fine!

the only thing that might stuff you up is the orientation / roation of the flange that bolts onto the cat. Hopefully all the hangers are in place. Some of those exhaust bolts can be pretty tight to remove!

good luck matey!

it's a hks 409 silent i've heard good things so everything should line up alright

fingers crossed

:(

Link to comment
Share on other sites

it's a hks 409 silent i've heard good things so everything should line up alright

fingers crossed

:(

the more room you have under the car the quicker you will do it as well.

with only 2 foot of room you are going to whinge and moan like i did when i did my r33.

Also it depends on if the exhaust fits under or over the back diff too .

and also sometimes getting those damn oxy sensors out can be a pain.. espec when the previous retard owner puts the wrong thead one in.

Link to comment
Share on other sites

perhaps dont do the above if the cat is still boiling hot from a spirited drive home!

hopefully he would only be spraying it only on the bolts and not all over the cat :P

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • OK so I just bidded $500 on an R33 GTS4 that no one seems to want. Waiting on a call from the agent to see if I won. 32 GTS4 is for sale. I can't deal with the temptation to mod it.
    • Might be there for work later in the year. Wouldn't mind catching up with you fellas - can't have too many beers, but will consume copious amounts of takoyaki while executing an asian squat on the side of the road while you blokes sort out your hangovers.
    • I know one example is a anecdote not data, but I'm running the same Aeroflow 525 at full voltage through a regular relay, and while I've had other fuel problems including melting the factory fuel hat, the pump itself has been fine for years. Of course, they aren't *that* expensive these days, you could swap in a new one and see if the issue is resolve. I think you had a previous thread about fuel problems, have you been monitoring and logging fuel pressure? Is there anything voltage related (for example does the voltage go up when the pressure goes down)
    • Slap a 460L into the car, send its mum.  
    • So last night pulling away from the lights, I lost power for about 1 second. Bit weird, but I kept driving... 5 minutes later the pump completely dies. When I tried to start the car, the pump won't even prime.  I left the car for about an hour, tried to start it and it all appeared fine. Pump primed, car started, got the fuel pressure I should have.... Start driving home, 5 minutes later it dies again. I'm stuck in a shit spot this time going up hill with a car right behind me, so I just let the car continue to turn over while praying to the fuel pump gods. After about 2 minutes of turning the engine over, the fuel pump came back to life and I got home (only about another 5 min away).  So I've been digging around online, it seems like the 525 fuel pumps really don't like to be run at 100% all the time. I've found quite a few examples online of people killing their Walbro 525 pumps within about a year of usage when they are run without PWM.  So, my pump is an Aeroflow 525 (AF49-1057) and I've been running it at 100% without PWM. I'm thinking the Aeroflow 525 didn't like being run at 100% and has burnt itself up.  I really am sick of dealing with fuel pump issues, my current thoughts are -  1. Use a Walbro 450 and run it without PWM. It seems like these pumps hold up pretty well to being run at 100% all the time. I only make about 350kw and can't see me making any more power any time soon so this is probably a fine option.  2. Get a Walbro 525, run it with PWM. I know doing this will annoy me as I feel like with only 350kw, its extra expense that I don't "need" and I'll be thinking the whole time while setting it up that I should have gone with option 1. I know I'll be happy with this option when its setup and running, its only the initial setup frustration and cost as an issue.  3. Get a Walbro BKS1001 brushless pump. This is the fu*k it I'm already going PWM, might as well go full retard. This option just seems better in every way, with the only downside being cost. But I don't know much about this pump so I could be wrong.  Happy to get everyone's thoughts before I go digging around in the fuel tank again. 
×
×
  • Create New...