Jump to content
SAU Community

Recommended Posts

i just bought a GTR and ill be pulling my EBC out of my GTSt to pu it into my GTR.

im not sure how to do it though.

there is 2 actuators for 2 turbos, so do i use a Y joiner to hook them both up to the solenoid? also im not sure where to hook it up to the FPR.

has any1 done it before? can you link pics?

cheers

Link to comment
https://www.sau.com.au/forums/topic/231505-greddy-profec-b-spec-2-on-gtr/
Share on other sites

yeah its pretty easy assuming you have the standard piping under the plenum.

the pressure source for the new solenoid is a vacuum pipe which is at the rear of the plenum (underneath) hook that to the input of the solenoid. the output of the solenoid goes to one of the 2 pipes under the plenum just above the oil filter (it comes from the standard boost controller). Not sure if it is the top or the bottom one off the top of my head - you need to trace it around the motor, it is the standard line that goes to both wastegates.

when you've done that you need to block 2 points in the standard pipes - the hose that you remove from the plenum needs to be blocked, and the other line that goes to the standard boost solenoid has to be dropped too.

this is the easiest way, you can retain all the standard piping and even mount the new solenoid where the factory one normally sits.

Im about to fit the same controller to my Autech Stagea. Pics would be a great help. so far ive spent nearly 4 hours searching the net for info on how to fit one of these to a GTR.....lol

will have 2nd attempt tomorrow at fitting it!

Edited by BIT SUS
  • 2 weeks later...
yeh its hard hey lol. unless i see some awesome pics ill be getting my mechanic to do it...

there is nothing on the net for the Greddy EBC into a gtr :dry:

you and me both man!!!!

FFS!

*takes a big deep breath

i sort of got a rough idea how to do it... just by tracing the vacum line from the wastegates of both turbos back around the plenum side of the engine but i lose sight of the line under the plenum lol....

its hopeless lol

sorry my next post went missing in the forum move. the top pipe of the 2 under the plenum is the one that goes straight to the wastgates. so give it a shot joeleo87

to make sure you have it right, turn the boost controller off (ie standard boost) pull 2nd gear on some open road, when you get to about 3500rpm if it goes over 14psi its not right....just get straight off the throttle if its wrong as long as you are paying attention everything will be fine.

sorry my next post went missing in the forum move. the top pipe of the 2 under the plenum is the one that goes straight to the wastgates. so give it a shot joeleo87

to make sure you have it right, turn the boost controller off (ie standard boost) pull 2nd gear on some open road, when you get to about 3500rpm if it goes over 14psi its not right....just get straight off the throttle if its wrong as long as you are paying attention everything will be fine.

so if its the wrong hose. it will just boost right up? and no damage whats so ever?

ill give it a go tonight duncan :(

if it works ill make a DIY!

um thats not quite what I meant.

If its wrong it will boost to eleventy billion - so if it goes past 14psi get straight off the throttle. If its wrong, and you keep your foot down you willl kill turbos and/or engine.

If its right it will stop at the right place and you will enjoy the extra boost :rolleyes:. make sure the controller is off when you test - this will mean you only get standard 12-14psi boost

i was thinking duncan, can i just replace the stock boost solenoid with the EBC 1?

or will that just poo things? to eleventy billion?

where do you hook up the unit's vacuum line? it says in the guide to connect it to the fuel pressure regulator? where might i find that?

photos would be a great help right now...

im lost :S

Edited by BIT SUS
where do you hook up the unit's vacuum line? it says in the guide to connect it to the fuel pressure regulator? where might i find that?

photos would be a great help right now...

im lost :S

thats the ezy part man.

if you follow the fuel rail (where the injectors are) at the end (radiator side) you'll find the FPR, there will be a small hose coming off it going into the engine, you put the 'Y' connection :P

The ezy way is to just replace the stock boost controler valve. Its very simple an is just as effective. I did my 32 gtr this way any had not problems.

I have also tried it with the controler mounted on the passenger suspension tower with the hoses cut in near the actuator's. It's a lot harder to do and you have to be confident with removing the top turbo pipes to gain access.....

Also as a note to all tune all the setting on the sontroler right down and slowly adjust them up...I started at about 50% on all settings and it was way to high. Start at about 5% on everything and work your way up to your desired boost setting.

i just installed the vacuum line to the Fuel pressure regulator. Ive got a strange feeling that my car is already running 14psi.. even without the solenoid connected up to the main unit. I hope not, cos then i will be dissapointed after my tune...

.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...