Jump to content
SAU Community

Recommended Posts

Hey guys,

Posting this for some info for a mate who got defected the other week. He has to get the car inspected by QLD transport now. On the back of the fine it says "A QLD transport authorised officer ... is to clear the defect notice and remove the defective vehicle label."

Does this mean the only things QLD transport are legally allowed to check are the defects listed on his fine? And if they can look for other defects, does that mean that anything they find will allow them to leave the defective label on the car?

He has called up QLD Transport and QLD Police but they give you a different answer every time. Useless.

Any help much appreciated guys.

Chris.

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/
Share on other sites

They can look at other things on the car that they might classify as defects depending on how much they stand out i guess.You can just get the car unregistered then they cant inspect it then.But he would have to get a roadworthy again but with someone who might turn a blind eye to the defect depending on how bad of a defect they are.

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4079796
Share on other sites

They can look at other things on the car that they might classify as defects depending on how much they stand out i guess.You can just get the car unregistered then they cant inspect it then.But he would have to get a roadworthy again but with someone who might turn a blind eye to the defect depending on how bad of a defect they are.

That loop whole has changed. Defect now has to be cleared (signed off as being fixed) even if you de rego then re rego with new RWC. In short if he doesn’t go get it cleared the Police will eventfully come after you, or just pwne you harder If they caught you driving it outside of the time frame given to have it cleared. This even goes for when you sell it. Get a defect, do the sly and de rego and sell with no RWC, new owner will be flagged at Queensland Transport when trying to get it re rego’d

Edited by Nismo_Boy
Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4079846
Share on other sites

my advice to ya mate is to look over the car and if he sees something that he is unsure about then i would remove it. unfortunetly he is branded by the cops so if he does something stupid again then they'll be harder on him next time. it has happened to a mate of mine, so after the first time he got caught, we keeped the stuff they got him for and just put it back on the car so he would be clear the insecption. unfortunetly thats how it goes.

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4079896
Share on other sites

  • 1 month later...

hey mate

I got defected about 3mnths ago a big delemar haha I went down to MJR Motorsports in burleigh and they cleared it all for me, cost abit but shud get u out of your troubles, either giive them a bell coz they are usually pretty busy with that kinda stuff but yeh give it a go and get bak to us

kinda regards

ash

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4149706
Share on other sites

OK, i asked my uncle on the weekend about defects.

anything that isn't stock standard on the car, DEFECT!!

that includes mag wheels, if they wanna get nasty.

so remember anything on ur automobile that isn't standard when it was brand new is a defectable item.

altho no points can be demerited for having a defected car.

and he said your run of the mill copper, wouldn't kno evrything about defective items.

but if ur pulled over by the dept of trans, ur screwed.

an a cop can't pull you over for defecting, unless they are possitive it's not standard for the car.

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4162936
Share on other sites

You can change mag wheels etc as long as they are in compliance with the QLD transport rules. IE they dont increase rolling diameter or width by X amount etc.

My 19 inch 235/35ZR19s are legal, however 245/40/ZR19s wouldnt be on my R34GTT

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4163005
Share on other sites

omy he is wrong then, you can be fined 75 bucks and 1 point for a defect or 300 odd (thats right right guys?) and 3 points for a major defect, They can now also send you to court and impound your car if they want and get caught and sent to court 4 times in 3 years and your car is gone. And cops can pull you over for defects if they chose, just the majority prefer to try to hide the fact they are and go for the random breath test or licence check instead

Link to comment
https://www.sau.com.au/forums/topic/232510-defects/#findComment-4165785
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
×
×
  • Create New...