Jump to content
SAU Community

Recommended Posts

first i sanded the parts with wet and dry sand paper by hand. i used three different grades, i think they wher 800 through to 1200. them use a stitch cotton mop(buffing wheel) on a bench grinder,(has to be at least an 8inch) use the stitched mop with a brown buffing compound. then once you get a shinny finish u use a different buffing mop(loose leaf) with a white buffing compound. and u can get it a shinny as i did.

u also need a spindle (adaptor) for the buffing wheel to fit on a bench grinder.

guys remember this takes hours to get the result that i got.

8 hours to do the rocker(cam) covers.

6 hours to do the intake pipe.

1/2 hour to do the CAS

and about 9 hours to do the plenum.

and this is only polishing time. not removing or fitting parts back on.

r31 skyline chick

ur plenum looks really good, who did you get it done by?

i was thinking about going in to business for myself and doing polishing full time. what do you guys think.

how hard will it be to mainttain that shine ? coz im getting my intercooler piping re-done in stainless so looking to shine up the engine bay... im willing to spend time into it, i dont have a bench grinder, rekon there's any other way for me to do it ?

DJ_L3THAL

i wipe it over every time i wash the car and give it a light polish by hand about every 3-4 weeks and still looks as good as the day i did it.

deffinetly cant do it unless u have a good bench grinder!

you wont even be able to use a angle grinder because u need the loose leaf mop to get the best shine. you could always do it by hand, but you would have to do a lot more sanding, and it would take you an eturnity.

Originally posted by walkoau

r31 skyline chick

ur plenum looks really good, who did you get it done by?

My other half does all my polishing.

And my metal fabrication, and all the other fun stuff that I can't do by myself.

I do the painting and ricing and cleaning.

Originally posted by walkoau

i was thinking about going in to business for myself and doing polishing full time. what do you guys think.

I think it's fine.... as long as you don't mind getting dirty.

:)

It's probably not as viable as it sounds.

Some things can be an absolute bitch to polish, my plenum has at least 8 hours work in it, and it still isn't perfect.

You need to take into account that if something so small takes a whole day to do, will people be willing to pay you a whole days wages just for one little shiny bit?

:)

r31 Skyline chick

yeah iknow what ur saying, but i dont mind getting dirty, im a heavy vehicle/plant mechanic by trade so im always dirty anyway.

DJ_L3THAL

i have no idea how much a pro would charge to do it. id imagime it would cost a fortune, but they would have all the right gear and get it way better then mine.

also i personally dont like the blue on my hose and wiring! i want to purchase some blue silicon hoses to replace the black one and get rid of the blue plastic.

rb20-calais

pm me. let me know when you want it done. if you can remove and refit ur self?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...