Jump to content
SAU Community

Whats The Best Computer

New Boy

By New Boy,
in Engines & Forced Induction

 Share

Recommended Posts

New Boy Apprentice

New Boy

Posted
Posted (edited)

hi im looking at getting a computer 4 my 95 r33 rb25det and i have had so many people tell me different things.. i have had rpm and Redcliff dyno tell me 2 go with the wolf 3d and other place 2 go with a autronic, and the power fc but i don't know who 2 trust. i'm going after 650bhp. and i have a rb30 in my shed 2 use.

please help

Edited by New Boy
Link to comment
https://www.sau.com.au/forums/topic/234216-whats-the-best-computer/
Share on other sites
New Boy Apprentice

New Boy

Posted
  • Author
Posted
how much do you want to spend

whats important to you

what engine / turbo setup

what do you expect from the ecu

around the 2500 or below

i wont something that will hold its tune

im going 2 build a 25/30 but 4 now just a rb25 with inlet plenum 80mm throttle body, top mount manifold waste gate. i haven't chosen a turbo yet

just 2 last and not keep having issues

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

The ECU is only as good as its tuner.

That said - see here:

http://www.skylinesaustralia.com/forums/Ma...html&hl=ECU

That thread basically covers the point as with the other 100's of "what ECU" threads that are around.

Thanks

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...