Jump to content
SAU Community

Recommended Posts

I got a infringement notice which says I supposedly didn't stop at a stop sign in crn of Campbell and Ramsgate Av in Bondi.

I didn't get pulled over that night or anything, and I don't recall this at all? What proof would they have to back this up?

Feel free to post of pm me your experiences.

Link to comment
https://www.sau.com.au/forums/topic/234959-can-the-cops-do-this/
Share on other sites

Can you afford a day off in court?

And do you want to fight it on principle?

If both of the above are a YES, I'd definitely fight it on the basis that

i) it may not have been your car or number plates being documented accurately

ii) it was night-time, so how could they identify that it was you in the driver's seat

iii) they haven't yet given you the chance to say it was someone else

iv) you've contacted your local MP and the transport minister Eric Roozendaal about it (reply pending)

v) you were somewhere else?.

Cheers

M :P

Yeh,

They can even send you EPA letters in the mail. Happened to a mate twice.

First time, was a cop walking on the street in the cross, copper walked up to his car told him he was going to get a EPA letter in the mail.

2nd time, was he just found one in his mail one day for him to visit to test the car under suspicious conditions. Got pumped. Twice.

I did know they could do this. And what was said above is a good statement, cause to be honest if I got it in the mail, I would of thrown it out until I get the reminder.

I'm quite sure the infringement notice should have some details about what evidence they have against you.

I just recently got one for allegedly "stopping on a pedestrian crossing" which noted that it was taken by a camera from Botany Bar Council.

Was gonna cost me $318 and 4 points, I didn't think they had a case with the camera since it was a 40 school zone.

The only reason I'd stop on a bloody pedestrian crossing would be if some stupid kids decided to cross the street a few metres ahead.

I took it to court and the infringement was changed to 'stopping on/or near a pedestrian crossing'.

Anywho pleaded not guilty and the Botany Bay Council dropped all the charges.

Waste of my bloody time yeah but at the end of the day:

$318 + 4 demerit points > my pay at work + how much I enjoy work

That's all folks

ii) it was night-time, so how could they identify that it was you in the driver's seat

iii) they haven't yet given you the chance to say it was someone else

I don't think it matters if you were driving or not. As it is the registered owner who is responsible for letting someone else drive their car, and the actions they take while doing so.

If it is someone else driving your car and they are willing to accept the blame then you both need to send a letter explaining who was driving and that they will accept the penalty..

Any time I have been accused AFTER the fact they only ever gave me a warning..

Yeh,

They can even send you EPA letters in the mail. Happened to a mate twice.

I got a fine in the mail that was as a result of report by a council ranger :3some:

I couldn't believe it.

I didn't have the time to fight it in court so I just paid it.

- Adam

I don't think it matters if you were driving or not. As it is the registered owner who is responsible for letting someone else drive their car, and the actions they take while doing so.

If it is someone else driving your car and they are willing to accept the blame then you both need to send a letter explaining who was driving and that they will accept the penalty..

Any time I have been accused AFTER the fact they only ever gave me a warning..

That's completely wrong. I think you're getting confused between traffic infringements and insurance claims from unnamed drivers. The registered owner can't possibly be responsible for someone speeding or running a stop sign in their car, just because it's their car.

The notice should be similar to the notice from a speed camera. The notices from speed cameras have a section stating that if you weren't behind the wheel you can send the form back with the details of the driver who was in control of the car and the notice is reissued to them. It doesn't matter whether that driver consents to that or not - they were doing the illegal thing, they get the fine. It's all on the back of the form, from memory. But that doesn't really apply to the OP, because he was driving.

Yeah i received a fine in the mail when i was helping my GF brother drop off the paper for his paper run.

I double parked in a quiet street and unloaded the papers from the boot to the foot path, was only stopped for 2 minutes. Costed me more then his paper round for a few months.

Didnt see anyone around no Police or Rangers.

That's completely wrong. I think you're getting confused between traffic infringements and insurance claims from unnamed drivers. The registered owner can't possibly be responsible for someone speeding or running a stop sign in their car, just because it's their car.

The notice should be similar to the notice from a speed camera. The notices from speed cameras have a section stating that if you weren't behind the wheel you can send the form back with the details of the driver who was in control of the car and the notice is reissued to them. It doesn't matter whether that driver consents to that or not - they were doing the illegal thing, they get the fine. It's all on the back of the form, from memory. But that doesn't really apply to the OP, because he was driving.

Iv'e never had to deal with an insurance claim like that, but I guess details could be mixed up somewhere along the line.

I say the registered owner is responsible as the rego plate is the form of identity when in a car. That Rego number IS you. (kinda) How can a police officer who sees your car run a stop sign possibly be expected to know if it is you driving or not? without actually stopping you. Not photo, just a rego plate..

If there is a photo which is clearly not you then fine, there is proof it was not you. But if there is no photo, just a police witness of the vehicle doing whatever infringment, How easy would it be to get off if I could just say it was joe bloggs over here..

For a matter of perspective, the next time you wonder about the traffic infringement you get either in person or in the mail have a read of this news article:

From 1995, the number of sexual assault clear-ups has more than halved, to 21 per cent of the more than 4000 attacks reported in 2007.

While they're not bringing rapists to justice, its heartening to know that the cops are fining people for the far more heinous crime of not stopping at a stop sign.

Cheers, guys.

Edited by scathing

Be a bit more constructive with your comment, mate. Highway Patrol officers don't go around trying to solve sexual assault crimes when they're not behind a radar gun - that's a totally separate facet of the Police force. If you're making a statement about the spread of Police resources, then say so. Blanket statements like that don't do anything for anyone.

Edited by HuH
If you're making a statement about the spread of Police resources, then say so. Blanket statements like that don't do anything for anyone.

I beg to differ.

Given the attitude that cops have towards the drivers of certain cars, and the special attention that they give to those cars regardless of if they're doing anything actually wrong, it would appear that the police feel that blanket statements and attitudes based on the visible minority covered by overhyped media coverage seem to be perfectly applicable.

Its the police force's job to catch criminals. If making blanket judgements based on tenuous evidence in tabloid media is good enough for people with the ability to restrict the freedoms of the populace, then surely its good enough for everyone else when determining their competence.

The main motivation behind my initial response to you was the knowledge of a Police presence here on SAU. Making comments like that outlining your blatent discontent with these law enforcers is probably not the best way to uphold the reputation of this club.

Having said that, there is some truth to what you're saying - specifically that a lot of HP officers do take special interest in Skylines and other imports - but being someone who drives a lot each week, I can understand why. I see so many idiots out there doing things that put people in danger, and if I was an officer myself I'm sure I'd probably have a similar approach.

Your post above certainly shows your penchant for wordiness, but it doesn't show much else. Your last paragraph says that the police place special focus on these imports because of what is printed in the papers? I hope you don't really think that. You think these officers need a tabloid rag to tell them that imports are the cars of choice for hoons? And the ones that they should take note of?

The whole situation is a catch twenty-two. Kids go out and buy these turbocharged cars that they're really not mature enough to be in control of. They spend thousands modifying them to be faster, look better, and to overall stand out from the crowd. This just accentuates their car even further when they choose to drive aggressively. I witness arrogant driving from a whole host of drivers out on the road, but it's much easier to blend in when you're driving a run of the mill car. Skylines already have a presence on the road, so when these owners choose to put some spirit into their driving - it's like putting a target on your back. Be responsible, and you'll be fine. That post you linked to doesn't show any qualities I disagree with. Buying a Skyline is buying into the hype. You will get pulled over from time to time, but if you're law abiding, there's no issue. If you're not keen on that happening, then sell the car - because you can't change it.

Edited by HuH
I got a infringement notice which says I supposedly didn't stop at a stop sign in crn of Campbell and Ramsgate Av in Bondi.

I didn't get pulled over that night or anything, and I don't recall this at all? What proof would they have to back this up?

Feel free to post of pm me your experiences.

In NSW there are two differing types of traffic infringement. One is called owner onus and the other is called driver onus.

Owner onus offences are camera related/parking offences where police do not have to identify a driver as the infringement notice is sent directly to theowner and the responsibility lies on them to identify the driver.

Every other offence is a driver onus offence. Polie must establish several proofs of the offence and one is "driver. They must identify a driver either by speaking to them directly at the time, or after the offence. They may also identify a driver by causing th owner to identify the driver.

Stop sign offences are a driver onus offence and rely on the police being able to prove who the driver is. If they have not spoken to you or the owner then you may want to take this further.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...