Jump to content
SAU Community

Recommended Posts

Hi

I have a series 1 R33 GTS-t. It has aftermarket alarm/imobiliser/central locking and usually it locks the passanger door when car goes over 25kmh

that was all fair enough as expected.

Recently, its been tempremental, sometimes it will work as just described, other times as soon as the ignition key is turned to 'ON' both doors lock immediatly. This happens more so at night then any other time :S

Started happening a week or 2 after wiring up a dual stage boost controller.

anyone have any idea whats going on here?

Link to comment
https://www.sau.com.au/forums/topic/235687-central-locking/
Share on other sites

Recently, its been tempremental, sometimes it will work as just described, other times as soon as the ignition key is turned to 'ON' both doors lock immediatly. This happens more so at night then any other time :S

it knows when the bad guys come out to car jack u! haha

sorry.. sounds really strange.. maybe when boost controller was wired up.. might have crossed wires or something

take it back to whoever wired it and tellthem your prob..

Link to comment
https://www.sau.com.au/forums/topic/235687-central-locking/#findComment-4126969
Share on other sites

i wired it, and all i did was run a wire from the stock plug for power, to a switch inside, back to the controller, then earthed to chassis.

Bit weird, didnt play with any wiring just fed a dual core (was actually formerly a power cord from some kind of appliance) through the firewall then pulled it through, did the switch.

everything was soldered and sealed etc etc.

so yeah a bit weird.

Link to comment
https://www.sau.com.au/forums/topic/235687-central-locking/#findComment-4127024
Share on other sites

maybe you might have to trace the wiring from the alarm and actuators, cause when mine was playin up the rubber housin around the wire had spit and the actual wire was exposed and everytime it earthed out it used to lok the doors etc.

Link to comment
https://www.sau.com.au/forums/topic/235687-central-locking/#findComment-4127053
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...