Jump to content
SAU Community

Defect Information

1st 32

By 1st 32,
in South Australia

 Share

Recommended Posts

1st 32 Collaborator

1st 32

Posted
Posted

Just wanted to clear up an issue I have recently came across and hopefully help out others in the same position.

Saturday just gone I was pulled over in my R32 GTS4 and defected for my front ride height being too low - ride height being the distance between the centre of the wheel cap to the bottom of the wheel arch.

The cop quoted the requirement for an R32 turbo as 360mm all round, leaving me a good 20-30mm too low at the front. It was recommended by a mechanic that I get confirmation from regency about ride height as he thought I looked alright.

Official ride height issued regency -

Front: 345mm

Rear: 355mm

Not the 360mm all round as suggested by the issuing cop!

At this stage I was a bit peeved that I got defected for something that did not exist???? Got onto the police and they were unable to say where the first cop cop his measurements from. Long story short a cop came to my place and remeasured by height and ended taking off my sticker - no longer defected!

For any defect I would suggest contacting regency yourself and asking for official confirmation on all info regarding your defect. Could save a lot of time, hassle and money!

Link to comment
https://www.sau.com.au/forums/topic/236312-defect-information/
Share on other sites
  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Cubes Grand Master

Cubes

Posted
Posted

Regency is the suburb location of Motor Reg where defects are inspected/cleared. South Aussy's have always called 'that' location Regency.

I might have to give them a buzz as 360mm ride hight sucks. I want to drop mine slightly.

Mine with std suspension was 355 front and 360rear full tank of fuel.

sneaky1 Mentor

sneaky1

Posted
Posted

also look at the rulings. might be a diff ride height from turbo and non turb cars. as well as the pre 1990 models maybe different too.

ring vehical standards and ask for clinton 1300 882 248. he is a good bloke that is rather cluey. ive delt with himmany of times and always came out with a good result.

nisskid Grand Master

nisskid

Posted
Posted
Just wanted to clear up an issue I have recently came across and hopefully help out others in the same position.

Saturday just gone I was pulled over in my R32 GTS4 and defected for my front ride height being too low - ride height being the distance between the centre of the wheel cap to the bottom of the wheel arch.

The cop quoted the requirement for an R32 turbo as 360mm all round, leaving me a good 20-30mm too low at the front. It was recommended by a mechanic that I get confirmation from regency about ride height as he thought I looked alright.

Official ride height issued regency -

Front: 345mm

Rear: 355mm

Not the 360mm all round as suggested by the issuing cop!

At this stage I was a bit peeved that I got defected for something that did not exist???? Got onto the police and they were unable to say where the first cop cop his measurements from. Long story short a cop came to my place and remeasured by height and ended taking off my sticker - no longer defected!

For any defect I would suggest contacting regency yourself and asking for official confirmation on all info regarding your defect. Could save a lot of time, hassle and money!

woh, im surprised they didnt come to urs and double defect u for other stuff :down:

Cubes Grand Master

Cubes

Posted
Posted
Damn that cop to hell. If it's your job to dispense the law - you have to know it. Quite simply that cop is an idiot. Unfortunately idiot cops are the norm nowdays.

I'm not sure.. I believe the minority of police spoil it for the minority. Much like the minority of import drivers spoil it for the majority in the public eye.

Today for example.. Police usually don't blink an eye but today just one little fat dude in an under cover car decides to stare as he drives past while I'm sitting at a round about.

Car doesn't look modified; 100% stock from the outside so really no reason. I haven't had that for quite some time. The last time I remember being stared at was a good few years ago.

He was probably one of the gtr bathurst haters. :)

Madaz Grand Master

Madaz

Posted
Posted
Regency is the suburb location of Motor Reg where defects are inspected/cleared. South Aussy's have always called 'that' location Regency.

I might have to give them a buzz as 360mm ride hight sucks. I want to drop mine slightly.

Mine with std suspension was 355 front and 360rear full tank of fuel.

Joel stick a GTS4 sticker on your car that will allow 345 and 355 :)

Pete its actually Fr 340 Rr 345

post-13315-1221570842_thumb.jpg

SUSPENSION

Transport SA

September 2003 Modifications to Passenger Cars, Car Type Utilities and Panel Vans Page 15 of 25

A vehicle's suspension system has been designed for adequate strength and durability as well as its level of ride,

comfort and handling. It is acceptable to fit upgraded springs, shock absorbers or anti-rollbars provided they

are correctly fitted and suitable for the vehicle. Some vehicle manufacturers have optional suspension

equipment available.

When lowering a vehicle body, either front or rear, the limiting factor is the clearance between the rubber bump

stop and the corresponding metal stop. This dimension must not be reduced by more than one third of that

specified by the manufacturer.

Transport SA has a list of acceptable suspension and eyebrow heights (the measurement from the centre of the

wheel vertically upward to the edge of the mudguard) for most passenger vehicles and can be contacted to

verify if the ride height of a vehicle is within acceptable limits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...