Jump to content
SAU Community

Recommended Posts

  • Replies 310
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I'll wait for the new hoodie to be printed, and have them both sent together. Less stuffing around, and i dont think i'll need warm clothes for a while now :nyaanyaa:

Cheers guys. Will check back to see whats going on with the printing fees, etc.

Someone hit me with a PM if need be :banana:

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4164102
Share on other sites

Yeah sure Carl, dunno when I'll get it though but at the latest it'll be monday on Damo's cruise.

Might see what I'm doing tomorrow before work, could you PM me your phone number so I can call before and make sure you're home.

Tom.

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4171119
Share on other sites

Yeah sure Carl, dunno when I'll get it though but at the latest it'll be monday on Damo's cruise.

Might see what I'm doing tomorrow before work, could you PM me your phone number so I can call before and make sure you're home.

Tom.

PM sent

btw i used to work at brighton foodies

FOODIES FTMFW

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4171640
Share on other sites

ok guys i have a new quote for screen printing and we will have to do a print/embriod to get the cheapest job

Print SAU logo and URL on the back and embroid our user names

now i know some people have spoken too me saying they want embroidery (well only 2) but personally i dont want to spend another $20+ on getting that done

i think a print/embriod should cost no more than $15 (to which i still dont want to pay :))

obviously will be cheaper the shorter your username i just need to get a price per character on embroidery but printing will cost $9.10 per jumper

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4186731
Share on other sites

Good work Steve.

So in my case, no username, means a total of $9.10. correct?

PM me about payment, along with your details etc.

cheers :)

Edit: So do you have our jumpers now?

Edited by Munkyb0y
Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4186771
Share on other sites

Sounds good to me aswell, will obviously be a little extra for my username but still sounds good :P

I think possibly once you get details on price for letters on usernames, start new topic for YOUR hoodies steve?

Link to comment
https://www.sau.com.au/forums/topic/237131-hoodies/page/5/#findComment-4186930
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...