Jump to content
SAU Community

Recommended Posts

complete oil cooler kit with oil filter mount so it can be bolted up to s13,s14 or s15 just be replacing the oil filter outlet that is provided. kit is used but still in great condition. has long braided lines and quality fittings. -$350 PRICE DROP $300!!! ....braided lines not pictured but do come with kit

oilcoolerco6.th.jpg

standard s13 fan shroud - $20

fanshroudzx2.th.jpg

17x7 skid rims. no tyres. good offset for s13. full set in good condition - $150

sellwheelsgs0.th.jpg

standard s13 k's model rear spoiler. good condition just dirty - $30

spoilerot5.th.jpg

s14 gearbox complete with bellhousing ect. SOLD!!!!

s13 bootlid. has origional hole welded up but has two small hole where a wing was fitted. painted matte black - $50

sany0334ou3.th.jpgthpix.gif

^^^^^2x fusion subs in custom box. 1 sub f**ked other sub works fine. sick of it taking up space in my room. -$100

complete series1 r31 front end minus bonnet. no dents. big scratched from sitting around. good for replacement panels. lights all work ect -$100

sany0335uo7.th.jpgthpix.gif

complete DR30 RSX interior minus passenger seat and dash. everything else there. including black carpet. everything in great condition. will give it a quick clean before sale. - $300 firm

sany0336ei9.th.jpgthpix.gif

sany0337ql1.th.jpgthpix.gif

DR30 RSX front struts and brakes. has electronic controlled damper adjustment tops. aftermarket springs and shocks. unsure of brands or rates but doesnt seem too stiff but rebounds well. $250 no pictures atm

S13 center console surround. good nic. $25

sany0338gt9.th.jpgthpix.gif

i am free all this week so if anyone wants to pick anything this week is the best. my number for quick contact is 0421 938 985. please no private numbers as i will not answer them

cheers

aaron

may trade for parts of interest like iron mask bonet and headlights with cash either way or a c210 manual tailshaft

you have the rear passenger electric window switches??? both L/H and R/H side ... I would snap up the Interior aswell but I have the other Red/Black trim

Edited by benny_blanco
do u have all 4 pwr window mecs? and interested in sending 2 Qld?

jon.

i have 2, but they are spares.

there IS however a TI near me, all window mechs are there.

they are a pain to remove as the screw is usually corroded or fused into the mount, si drilling is required

if you REALLY keen, let me know how much you wnat to pay for them, and I will go sort it out.

Postage willo likely be $30 as they weigh a fair bit

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...