Jump to content
SAU Community

Recommended Posts

Hello,

I have a 1992 nissan skyline gtr with 18x8.5" on the front and 18x9.5" on the rear with unknown offsets and unknown spacers so I am running just rwd for now but I would like to run awd and I would like to get rid of the spacers because they are not hub centric so the car shakes at around 100km/hr. Hence, I would like to run 18" rims but I need help choosing an offset and rim width. I have found that I need a rim with a centerbore of 66mm but I cannot find a common response to the offset and rim width.

Thanks,

Justin

if you are looking at 18inch then 18X9 with offset between +30 and +18 will be suitable. or 18X9.5 with offset between +30 and +22 is good too. tyre size either 245 or 255 will be fine too. then you can chuck out your current mismatched wheels and frisbee the spacers over your back fence!

the PCD is 5 X 114.3.

a popular choice is R34 GTR wheels which come in 18X9 +30 and look great on a 32. they fit perfectly, are forged (so light and strong) and can be had for reasonable money.

so you get these (my 34):

zimg8127wm5.jpg

and put them onto this (my old 32)

p1sve7.jpg

Hello,

I have found some bronze Nismo wheels for the 2003-2008 350Z fronts. They are 18x8.5's with a 25 offset. I found them for $800 and apparently they are new. Do you think they would work and look good?

Thanks,

Justin

they will fit "okay" but in my opinion not quite the right size or offset for a 32 GTR they will look too narrow for such a tall wheel. ideally you want a nice 18X9 +20. that will be perfect. also it makes it far easier with the 4WD if you stick to the same size and offset all round and use the same tyre size all round. also means you can rotate tyres front to back to get more life out of them. :rofl:

  ISC-Performance said:
I have 18x9.5 +20 wheels on my R32 gtr and the wheels/tryes sit about 5-10mm inside the gaurd. perfect for what I want, no scrubbing etc.

Ryan

What size tyres do you run on those wheels??

I am considering 17x9.5s or 17x9s for my R32 GT-R, trying to research whether the 9.5s will fit ok (the wheel I am looking at is a +17 offset in the 17x9.5 size - Work Emotion XD9)

  thebuzz said:
What size tyres do you run on those wheels??

I am considering 17x9.5s or 17x9s for my R32 GT-R, trying to research whether the 9.5s will fit ok (the wheel I am looking at is a +17 offset in the 17x9.5 size - Work Emotion XD9)

yep - 9.5" wide fit no problems. I run 18"x9.5" with a +13 offset and they are probably right at the limit.. and that's running 265/35's.. but a +17 will be 4mm further in, so should look good and give you that little bit extra guard clearance.

  • 2 weeks later...
  4jo3 said:
Hello,

Thanks you have been alot of help, I found a set of r34 gtr rims but the previous owner says that he is using spacers? Why would he do this?

they dont quiet fill the guards, i ran about an 8mm spacer when i had 34 wheels on my 32 gtr they would sit just inside the guard.

Gtr1732005.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
    • Continental have consistently beaten the absolute shit out of every other performance tyre in Wet/Damp/Cold conditions and give up a little bit of time (half a second at most) in the dry. Almost like it's engineered for German conditions or something. I'd def give those a try.
×
×
  • Create New...