Jump to content
SAU Community

Recommended Posts

im finally getting to the final stages of my build

i need a ecu pinout diagram for a r33 gtr so i can wire up the harness for my d jetro

also how would i connect my apexi power fc boost controller with my d jetro?

need urgent help

thanks in advance

brembogtr

Link to comment
https://www.sau.com.au/forums/topic/239450-rb26-r33-ecu-pinout-diagram-needed/
Share on other sites

here's a pinout i found. Its for a 32 gtr, but they the power fc's are interchangable with 33gtr so i guess they are the same.

right here on SAU.

http://www.skylinesaustralia.com/forums/in...st&id=26367

here's a pinout i found. Its for a 32 gtr, but they the power fc's are interchangable with 33gtr so i guess they are the same.

right here on SAU.

http://www.skylinesaustralia.com/forums/in...st&id=26367

I have an R33 RB26DETT manual but it is in PDF form so I can't copy and paste from it (although if you are real keen send me an email address and I will send you the whole file as an attachment).

However the R32 pinout above is pretty much the same with the following differences:

*The R32 pinout diagram lists pins 109 to 117 (missing 113). I think this is just a typo as the chart goes from 109 to 116 inclusive.

* pin 6 on the R33 is blank

* pin 104 and 106 are the other way round!?

*pin 17 RB33 says Ïnjection pulse (Ti monitor) signal

*pin 109 RB33 says ïnjector power supply (counter electromotive reflex circuit) " maybe the same thing?

*pin 115 RB33 says: Exhaust gas sensor heater ground

Otherwise appears to be the same.

thanks for the reply's very helpfull!!

kiwirs4t if you could please email the whole file to [email protected] i would really appriciate it.

does anyone know anything about connecting the power fc boost controller when using d jetro?

thanks again!

thanks for the reply's very helpfull!!

kiwirs4t if you could please email the whole file to [email protected] i would really appriciate it.

does anyone know anything about connecting the power fc boost controller when using d jetro?

thanks again!

Sorry i tried to email the file but after uploading for half an hour on my so-called broadband connection I had to go to work so left it running and when I came back it had failed so i guess it is too big.

I bought a whole CD of manuals off "Chook" (Simon) on this website.

...Bob

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...