Jump to content
SAU Community

Recommended Posts

Hey,

Noticed a slight problem with my r32 gtst.

What happens is;

if i take the car for a drive (20-30min peak hour drive etc)

Then park it and turn off the engine.

Then start the car after 5-10 minutes.

And let the car idle stationary in traffic.

The idles drop below 500rpm and the idle starts going up and down and sounds like its missfiring.

Once i get some space to move forward, the car is real hesitant (feels like ignition timing drops to 7~ or not building any boost in first gear.) Once i shift into 2nd gear everything is back to normal...

I noticed this problem after replacing my O2 sensor with a new NGK sensor, but i have my doubts its related to that?

Also, ive noticed on cold morning startups/drives, the ignition timing tends to drop to 7 whilst driving and you can feel the hesitation. After the car is warmed up, this doesnt happen, so im assuming its just the ecu running on cold start mode, but it has never been this obvious in the past 2 years..

At one point, i had an ecu error of faulty knock sensors appear, but cannot seem to get the same outcome again.

Car has new splitfire coilpacks, ignition module, new battery & new alternator. So im sure it aint an electrical issue.

Im thinking its either the o2 sensor or the ecu?

Cheers

Patrick

Link to comment
https://www.sau.com.au/forums/topic/240253-lumpy-idle-after-hot-engine-start/
Share on other sites

update;

during the dodgy idling, my igntion timing fluctuates from 13-15 degrees.

Each time it drops to 13/14 is when the car starts acting all funny, and then goes back up to 15 where it calms down..

Is this a faulty CAS?

could it be a fueling issue?

Ive got a GTR fuel pump, and dyno runs show there are no signs of any leaning out etc.

Would a faulty cas make the ignition timing fluctuate which then affects the idle?

This only happens once ive started the car after 5mins of turning it off.

Then, once i hit the first set of traffic lights and idle, the rpm's start fluctuating.. After i move off and continue driving, the problem doesn't occur again..

Hi there Rekin,

I have a r34 gtt and have a similar problem i can drive my car to work in the morning ok but on the way home and by the time im home the car is missfiring realy bad and when getting on boost the engine just breaks down , the other night i had to use the wifes car it was that bad. So have found out what the problem is yet ?

Im putting new plugs in friday and i have ox sensor coming somtime this week.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...