Jump to content
SAU Community

Recommended Posts

One thing I've learned about car stuff is if it does the job, there's no sense in upgrading.

Royal Purple may be the best, but if your box and diff are fine with Redline, what are you actually paying for?

Link to comment
https://www.sau.com.au/forums/topic/24047-royalpurple-oil/#findComment-514718
Share on other sites

I have a hot4's engine oil test, where they compare dyno figures with different oils, same car, same day, same temperatures.

The two best oils were...mobil1 which gave as far as i remember about 6% over the control oil,

.............but then...they tried royal purple, and it was unbelievable!! It was some crazy figure like 10-11% power gain over the control oil!!

So if you can afford it, try it, i would.

Link to comment
https://www.sau.com.au/forums/topic/24047-royalpurple-oil/#findComment-515044
Share on other sites

Yeah, its the Mobil Super Syn formula. About time it came out. Its been in the US for over 1 1/2 years.... And RP is a bit overhyped IMO. It doesnt show anything special in UOAs (Used Oil Analysis) in various cars compared to other Synths out there.. But if it floats your boat.. hehe

Link to comment
https://www.sau.com.au/forums/topic/24047-royalpurple-oil/#findComment-519533
Share on other sites

I don't know if you guys realise, but this "extra power" from changing oil has to come from somewhere. While viscosity will play a part in the velocity of the reciprocating parts and limit/affect power production, i would think that the primary difference is that the oils that produce more power are less wear tollerant; ie while they are still protecting your engine, they are more prone to wear. Consider that a thicker oil will provided better protection, but will rob power; by the same token a thinner oil will promote the engine to spin more easily but all thing equal it will not protect as well.

Link to comment
https://www.sau.com.au/forums/topic/24047-royalpurple-oil/#findComment-519785
Share on other sites

Higher viscosity does NOT equal better lubrication unless you're running extreme type engines (ie, 1000hp+ drag cars). For most of our cars, if the rings and valves are still good, a 30 or 40 weight oil is good enough. Any thicker and you lose power for no real gain.

The benefits of thicker oil in normal cars appear when your rings start to get a little worn, and the thicker oil will help seal the gaps a little better so you don't burn as much.

Link to comment
https://www.sau.com.au/forums/topic/24047-royalpurple-oil/#findComment-519788
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...