Jump to content
SAU Community

Recommended Posts

i'm in but at jem they said i had some high end pinging and that thing sitting at the front of the rb25 engine had to be moved clockwise by a mm or something, the guy just loostend the bolts and tapped it around a few times with a spanner and said that should be it...... he didnt re dyno it to see if the pinging did go away....

if its not it and the guys at uas says there some pinging and that thing needs to be moved around again will they do it???? it only takes a minute to do but you need a dyno to know if the prob has been fixed..... i really dont care if they wanna charge me for another dyno run (id rather they didnt charge me for another run) aslong as the prob is fixed because at the moment i'm advised not to let the revs get past 7000rpm or risk damage to the head gaskets or something.....

also should have a fmic by then, mabey a boost controller

if youve got logs of your car pm me and I can have a look at your logs and ecumap if you want

  • Replies 225
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

lol no you wont ill be on a skidpan instead

Get your boat ready!

I was thinking of trying to sneak a bottom end build in before this but even if I have what is called good luck for me I might get it back 2012 :wacko:

See you near the frying pan

I made a post saying I'm interested in this, but am still fairly clueless has to how a "dyno day" actually goes. Do I just rock up with my car and put my name on a list? What happens next? :>

Edit: Just to clarify, I know what a dyno is. What sort of knowledge can I come away with from a dyno day?

Edited by mic0r

Yep you show up whenever you want, then see one of the people with an SAU shirt on (wont be hard to miss, one will be holding a clipboard), so over and say hi, then its basically a case of "join the back of the line" :P

if youve got logs of your car pm me and I can have a look at your logs and ecumap if you want

hey you were at jem on sat,,,,, pretty gutzy rex you got ther 190ish kw right???? i have no idea what you just said so i'll just say "YES" lol, what area you at though????

I made a post saying I'm interested in this, but am still fairly clueless has to how a "dyno day" actually goes. Do I just rock up with my car and put my name on a list? What happens next? :>

Edit: Just to clarify, I know what a dyno is. What sort of knowledge can I come away with from a dyno day?

You pays your money and you gets your car puts on the dyno. They runs it 3 times and then gives you a print outs of the power and the AFR (air/fuel ratios) and the boost. They tells you if it is running ok or too rich or too lean or pings so you knows what condition your tune is in. You gets to see how much powers you gots and if your boost holds steady. You gets to see how rich or lean your AFR's is.

Dont like my chances of winning, do like the idea of setting my rears on another dyno to confirm the performance results.

Can we have highest highflow category? lol

I don't like the idea of creating a category just so I can win it. :D hehe




  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...