Jump to content
SAU Community

The "end All" On Rb25 Coilpack Failure Misfires?

Travis Bickle

By Travis Bickle,
in General Maintenance

 Share

Recommended Posts

Travis Bickle Collaborator

Travis Bickle

Posted
Posted

I am somewhat new to skylines. previously i owned a gti vr6 which is notorious for coilpack failures due to super high underhood temps.

i never gave it much thought on the skyline until it started to misfire the other day. i started with the obvious and tightened all intercooler piping ect ect.

it had to have been the coilpacks at this point so before i went out and spent 600 bucks on splitfires i decided to take a look at what i was working with.

i pulled all 6 off individually and sprayed them with chem elect cleaner to get a better look. immediately upon looking at the epoxy they are made of, i thought "oh damn, its a single version of the VR6 coil" (the VR coil has all six prongs on one unit)

simple fix, cost me 3 dollars and i probably wont have to do it again.

JB WELD

jb weld, is good to 600 degrees C and is the same composition, albiet a bit stronger than the epoxy on the coils.

lightly coat the expoxy area on the coilpack that is cracked. let dry. i even used the fast setting kind, as i have used this on my VR with great results. is it ghetto? as i have always said "if you do a great job is hard to tell you have done anything at all"

i just did mine, and it runs like new. i didnt take any pics, but here is a picture of a VR6 coilpack with the JB weld on it for reference. hope this saves someone 597 bucks and a ton of headaches.

jbweld.jpg

Godzilla32 Veteran

Godzilla32

Posted
Posted (edited)

The problem is they are known for hair line cracks on the front of the coil pack not so much through the epoxy.

BTW blown intercooler pipes wont cause a misfire mate. Better start that apprenticeship lol

Not to mention they are 15 year old coil packs, with 15 year old windings. So a cheap fix isnt always a permanent fix. There are different reasons why coil packs fail and you can't assume they are all for the same reason. So no, its not the end all to coil pack failure.

Edited by Godzilla32
Travis Bickle Collaborator

Travis Bickle

Posted
  • Author
Posted
The problem is they are known for hair line cracks on the front of the coil pack not so much through the epoxy.

BTW blown intercooler pipes wont cause a misfire mate. Better start that apprenticeship lol

Not to mention they are 15 year old coil packs, with 15 year old windings. So a cheap fix isnt always a permanent fix. There are different reasons why coil packs fail and you can't assume they are all for the same reason. So no, its not the end all to coil pack failure.

so a crack in the epoxy, cant be fixed with jb weld? LOL

and when i say misfire, insert the word "sputter" when talking about loose piping. same sympton. bwaaahhhhh brrbrbrbbrrbrbrbrbrbrbr

worked great for me

Godzilla32 Veteran

Godzilla32

Posted
Posted

Well the front of the coil pack isnt epoxt its plastic and all kinds of repairs have been trialed and none are permanent. There is a big different between over fuelling (blown IC pipe) and a missfire.

Well as long as it worked for you thats great ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ShezzDogs
      R34 Skyline Sunroof Won't Tilt/Vent

      By ShezzDogs · Posted

      Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...