Jump to content
SAU Community

Recommended Posts

Cant help myself this time , something for petrol heads to think about and a bit of drag queen drama blog over C02 and global warming .

http://blogs.drive.com.au/2008/07/v8_supercar_greenwash.html

Something to read if theres nothing doing ATM .

Enjoy , A .

Edited by discopotato03
Link to comment
https://www.sau.com.au/forums/topic/240739-more-e85-blogblather/
Share on other sites

I'm not so sure the tip in 30% more fuel idea is what you have to do real world . E85's ability to run more advanced timing I think means the mixture strength may not have to alter as much as say ULP to make the same torque numbers .

Also to some degree spraying in a bit more (by comparison) can have some advantages like evaporative cooling (charge air cooling) so it's not all necessarily bad . I think it's a case of a bit more ign advance/a bit more charge cooling/a bit of this a bit of that and over all making it all work in positive ways .

It's early days for tuning E85 in Australia and I have every confidence that Ausie tenacity (Sp ?) will ring every ft/lb out of this stuff - given time .

The BIG thing is getting the fuel distributors to market it everywhere and what's holding that up is the lack of flex fueled OEM cars . SAAB has one and the FF'd VE Commode Door is supposed to be in the pipe . It's a sort of chicken and egg thing with the chichen run being expensive (I did read US 200G to install approved E85 tank and pumps) and a luke warm interest in the eggs . The fuel suppliers want to be confident that their investment in equipment is not wasted so the toe in the water exercise can take time .

Overseas there have been tax breaks with E85 and it remains to be seen whether our Governments will favour incentive over revenue . If it gets tax breaks here the cost/consumption ratio needs to be line ball or better to encourage Mr Mrs people mover to buy it . We as "timing lords" want it for other reasons but we are a very small component of the buying public .

In time , cheers A .

Said to have more hydrogen and less carbon than ULP so on the swings and roundabouts less C02 you'd think . Have seen mention of much less HC and with lower combustion temps possibly less nitrogen oxide aka NOx .

Like all consumer goods the focus is on price , some want the physical benefits and others get wet over the "green" aspects . If you can have it all go for it - I wish the fuel suppliers would .

A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...