Jump to content
SAU Community

Recommended Posts

  • Replies 188
  • Created
  • Last Reply

Top Posters In This Topic

Just thought I'd clarify for you guys wanting to block bov the coke can does the job perfecty. I did it today just for Shit and giggles and took me a whole 15 min just make sure you trace the bottom of bov on can and cut around the trace place cut out in between bov and the intake pipe mount Put back together and vwallahh you have flutter tutututu.

Btw this was performed on a standard bov and with a k&n pod filter.

Edited by Vlasi

Hahahahaha that's funny as madaz. skyhi its short for a blow off valve it is a valve that allows boost pressure leave your turbo system also makes A tsuuuuuu sound with standard bov and pod filter and you can get after market bov that makes a more defined tsuuuu sound

also makes A tsuuuuuu sound with standard bov and pod filter and you can get after market bov that makes a more defined tsuuuu sound

so, this tsuuuu sound, what does it do? like, i see the original bov has more u's after it therefore its a longer kind of sound right?

Edited by SkyHi_33

Some how this trick saved my a** tonight when the cops were doing their "part 2" at a RBT tonight. They were after a atmo BOV and they watched it while they got me to rev the hell out of the engine. All they heard was tsuuuuuuu from the turbo, then they were like that's ok!

Sometimes i feel sorry for them as they obviously did not have a clue, twice they looked over the engine bay before they asked "Where is the Blow off valve?"

My god they over looked the boost controller and solenoid, FMIC, POD, Exhaust, rim spacers, etc. Makes me think i could of had a high mount turbo and NOS kit and they still would just be after a BOV.

Madaz, they were pretty good about the whole thing but i remembered what i read sometime ago about these things. Which was not to offer too much info about anything in or on the car.

So that was you scandyflick out the front of Mayne Pharma that time? Its on the camera's man and she was actually 45!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...