Jump to content
SAU Community

Recommended Posts

Took it for a run on PRIVATE PROPERTY (cough cough) and it sounded great... none of those stalling issues either...

As mentioned in above post, you can drive it softly with no flutter and if you want it to flutter just give it some stick!!!! :)

All is good...

(now to take it off so that i can drive on the public roads again withought being defected by the boys in blue....)

Mine is the other way round. I got a HKS 2530 and a Greddy BOV plum back and has flutter at low revs and in med revs you get flutter then a little psshhh and when i give it stick i get alot of pshh and very very small flutter. I have an adaptor plate between the pipe and bov which i need to check to see if it's blocked or not. Sounds awsome but thinking of going back to stock just so it's one less thing the cops can pick on.

  • Replies 188
  • Created
  • Last Reply

Top Posters In This Topic

Yea, I know what you mean dude! It's one of the first things cops look for... And who's to say some cops won't b sitting in a shopping centre car park when you go to change gears...

All of a sudden you see, two red and blue flashing lights in your rear mirror and hear woop woop!!! :(

is it true that some people have been pulled over and asked to rev their car???

That's why I was trying to find a way of blocking it off making it look stock but also wanting some flutter when I give it a good bit of stick...!

:)

Mine is the other way round. I got a HKS 2530 and a Greddy BOV plum back and has flutter at low revs and in med revs you get flutter then a little psshhh and when i give it stick i get alot of pshh and very very small flutter. I have an adaptor plate between the pipe and bov which i need to check to see if it's blocked or not. Sounds awsome but thinking of going back to stock just so it's one less thing the cops can pick on.

Chestnut, the spring rate in your BOV is what is causing the flutter on throttle release on low pressure and has the wssssh on throttle release after giving it plenty. I would highly doubt that you would have the BOV blocked off.

I am running the standard BOV in the sedan, and it flutters in gearchanges under load/high boost.

Only mods that i think contribute to this effect are the trust metal intake pipe, the standard BOV return pipe (which has been slightly modified to accomodate the metal intake), and the blitz pod filter. So it's a very standard looking set up. No coke can / blocking plate bizzo

I am running the standard BOV in the sedan, and it flutters in gearchanges under load/high boost.

Only mods that i think contribute to this effect are the trust metal intake pipe, the standard BOV return pipe (which has been slightly modified to accomodate the metal intake), and the blitz pod filter. So it's a very standard looking set up. No coke can / blocking plate bizzo

Take you BOV off and you might just find it been blocked by a coke or JD can :P

well seeing as its another SAU;SA members old car, do you know something I don't Krish? LOL

I haven't seen anything like that though, have taken the crossover pipe off a few times now to replace plugs etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...