Jump to content
SAU Community

Recommended Posts

hey all got a few parts here that needs to go

all parts are located in SA, prefer pick up only or post within SA only

HKS 2540

post-38352-1225070071_thumb.jpg

very good condition, has a garret compressor housing

to suit RB20/25

asking $900

R32 Greddy Type S coilovers

post-38352-1225070304_thumb.jpg

excellent condition only done 1500km on these, comes with C spanners

asking $1450

RB20DET

engine has done 158,000km always serviced with motul oils and fluids

comes with loom and computer, has braided oil and coolant lines, minus turbo (can arrange standard turbo for extra $) price has been adjusted to suit

asking $1300

RB20 Gearbox

good condition, hasnt been treated harsh rear main seal done about 5000km ago

asking $450

Genuine GTR front bar and front guards

R32 GTR front bar genuine plastic item in painted matte black, good condition $300

R32 GTR front guards, alright condition, very light weight compared to GTST guards $350

can call/sms me on 0431171992

pics will be up on other items tomorrrow

Link to comment
https://www.sau.com.au/forums/topic/241902-r32-parts/
Share on other sites

what engine was the turbo on?

how much power was it making?

when did it hit boost?

how many k's old?

cheers

hey mate the turbo was on a rb20 and it made 200kw on morpowa's dyno running 1 bar boost, wasn't running bigger injectors and only a FMIC and 3inch exhaust

its been a while since i drove the car soo i would say it hit full boost at around 3500-800

the turbo was second hand when i bought it and since i had it has done about 10,000km

Link to comment
https://www.sau.com.au/forums/topic/241902-r32-parts/#findComment-4222319
Share on other sites

Hey man you wouldnt sell those coolant and oil lines would you?

Im after some RB20 parts,

* turbo coolant line that goes around the head.

*ECU temp sender, big yellow one

*turbo to mani nuts

Link to comment
https://www.sau.com.au/forums/topic/241902-r32-parts/#findComment-4231227
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...