Jump to content
SAU Community

Recommended Posts

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Head already in use on my other engine.

Willing to sell the complete bottom end for $400 will even throw in a standard plenum(minus fuel rail)

New OEM headgasket to sump. No pumps or alternator.

Has low comp in no. 5 cylinder.

Just needs a freshen up, whack in some forged pistons and your set.

RB25DET bottom end

2x standard plenums

1x standard complete fuel pump

Misc. bits and pieces

Take it all for $400

Need to clear some room!!!

  • 2 months later...

thanks mate about those lifters sorry dude im kinda new to this forum thing, dont laugh but what does PM mean. lol. and also have the lifters been sitting in an oil bath or are they still on the head itself. Ill pick them up or get you to send what ever suits you. id rather pick up though, if you havent sold them.

thanks mate about those lifters sorry dude im kinda new to this forum thing, dont laugh but what does PM mean. lol. and also have the lifters been sitting in an oil bath or are they still on the head itself. Ill pick them up or get you to send what ever suits you. id rather pick up though, if you havent sold them.

The lifters are sitting on a shelf in my garage (not in an oil bath)

They are still there so if you want to pick them up then thats fine.

  • 1 month later...

hey mate

still havent heard anything about those lifters mate. can you let me know who you sent them with so i can give them a call and see where it is. Sorry mate but i really need them or ele i wouldnt be busting balls. i was hoping to have them this weekend.

cheers

ayhan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...