Jump to content
SAU Community

**cusco-10point Rollcage**

Antonjj
 Share

Recommended Posts

Antonjj Enthusiast

Antonjj

Posted
Posted

i have for sale a CUSCO 10-point rollcage for a bnr32 gtr. i bought this brand new while i was in japan, with plans of putting it in my drift car when i finished it but plans change and no time for project.

$1800ono

post-48873-1225687836_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/243079-cusco-10point-rollcage/
Share on other sites
femno Grand Master

femno

Posted
Posted

Just wondering what classifies it a being a 10-point cage?

Have seen others labelled 6-point with the same amount of parts etc.

Did you find out what material its made of yet?

[WLDCRD] Mentor

[WLDCRD]

Posted
Posted

its basically a 6 point but you got the attachments that go from the b pillar hoop to the a pillar legs which run alongside the doors and the bar that goes from the top right side of the b pillar loop to the bottom of the left of the rear arm.

And as far as i am aware its a safety 21 cage which i thought were all black and steel and the chromoly ones are the blue ones.

GTRBOS Mentor

GTRBOS

Posted
Posted

its basically a 6 point but you got the attachments that go from the b pillar hoop to the a pillar legs which run alongside the doors and the bar that goes from the top right side of the b pillar loop to the bottom of the left of the rear arm.

And as far as i am aware its a safety 21 cage which i thought were all black and steel and the chromoly ones are the blue ones.

your exacely right there mate, got to it b4 i did :cheers: , black ones are steel which are heavy and ofcourse the cheaper ones but the blue ones are the leightweight material cages which are the pricey ones, i think this is abit pricey what his asking but hey its his cage, you said you will get rid of it for 1k and my offer was $650 which i think is a pretty decent offer,

cheers mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • Dose Pipe Sutututu
      Valve clearance for RB25det series 2

      By Dose Pipe Sutututu · Posted

      This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • GTSBoy
      Valve clearance for RB25det series 2

      By GTSBoy · Posted

      This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Kinkstaah
      Valve clearance for RB25det series 2

      By Kinkstaah · Posted

      Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...