Jump to content
SAU Community

Recommended Posts

It was just the thing my gearbox needed.

I was already using a PENZOIL synthetic gearbox oil but changing from 1st to second fast would still cause a slight crunch.

with this oil it works great.

Just remember one thing though.. Once you put Synthetic oil in your gearbox, You CANNOT go back to an organic oil.

FLY-SKY..

Maybe what that means is that it is not suitable for use IN the rear DIFF and to use it only for gearbox.

hey guys any one know anything bout gear boxes??

cause yesterday i put a 2nd hand box in and now when i give it abit of revs the car feels shakey, feels like its the tail shaft or mayb the fly wheel... or does anyone think its the actual box itself?? its second hand i wouldnt know if anythings wrong with it... help would be greatly appreciated, thanks

did you use your original flywheel? the tail shaft would be hard to put in wrong because of the spline on the end, and the gear box would work (my guess) if the internals weren't lined up as they should be!!

sounds like clutch plate/fly wheel issue IMOH

I don't know if anyone's tried this, but I found that adding oil stabiliser (Lucas or Morley's) to my gearbox improved the action a good deal.

Despit my box having been re-built (due to slow undiagnosed oil leek, not thrashing) it was still a bit notchy. I decided to try oil stabiliser firstly before going to the expense of using Redline.

The oil stabiliser label says very worn boxes need 40%/normal oil mix. I tried this firstly and found it too difficult to shift when the box was cold. I re-mixed the formula to 30% and it was much better, but still a bit stiff for the first couple of shifts (I am mixing it with Castrol VMX80). Probably a mix of 20% would be ideal, but I'm leaving it as is cos it feels very smooth once it's warm.

It only costs about $19.00 for a litre, and you only need about half that.

Anyone got any comments on the rights or wrongs of doing this? I mentioned it to my mechanic (Gavin Wood, Autotech) and he had nothing against it.

Lucas is just an oil thickener really. I didnt think it'd do much for shifting. Also lucas causes real bad foaming from some tests i've seen, so I personally wouldnt recommend it.. But hey if it works for you..

Originally posted by Timmy G

you cannot go back to organic oil because synthetic is so good and feels better? or it'll physically damage your box?

I mean you can't go back because the REDLINE synthetic oil leaves a coat of film (like a coat of oil) in the gearbox and I've been told that you can't mix organic oil back in to it or you'll get CLUMPS of crap in the gear box oil.

Redline oil costs $25 a litre.

The R32 GTST gearbox takes 2.8L

I bought the large 4 litre thing for $100 and have about a litre left.

When you consider that you probably spend at least $50 every 5000kms and never change your gearbox oil until you feel a problem, it's a wise investment.

  • 2 weeks later...
Originally posted by Busky2k

Lucas is just an oil thickener really. I didnt think it'd do much for shifting. Also lucas causes real bad foaming from some tests i've seen, so I personally wouldnt recommend it.. But hey if it works for you..

True - Lucas and other stabilisers are oil thickeners (or certainly appear to be even though Lucas claim on the website that their stabiliser doesn't alter VI), but Redline Lightweight Shockproof is simply a thicker oil (80w120). There is nothing exclusively esoteric about it, and it is very expensive.

I can't recall the VI for Lucas' stabiliser, but you could beef up a 75w90 synthetic with it to about a 120 oil simply by doing a few sums - or do what I did and just follow Lucas' instructions for a 20% concentration.

It'll still mean you get all the protection and longevity of the synthetic and at a fraction of the cost of the Redline.

Shell Helix 75/90 is a fully synthetic and is 'water cracked' so it's cheaper - about half the price of Castrol synthetic. It's probably a good oil but might not have quite the drain interval of, say, Castrol.

As I said, my gearbox was still a bit notchy after the re-build, but is now so smoooooth, and I think it cost me about $37 for both the synthetic and the oil stabiliser.

I don't know about the foaming issue Busky mentioned, but in the end it is the quality of the shift which is one of the main indicators of how a gearbox oil is working.

Lucas is frequently used in competition.

I'll be posting a new thread shortly with independant analysis of various oils in use (as soon as I find where I put it) which also shows that you can't believe didly squat about oil company claims concerning their products.

I'm not suggesting Redline isn't a good oil, just questioning whether we need to spend all that money for non-competition use.

  • 1 month later...
Originally posted by BuzLightyear

I don't know if anyone's tried this, but I found that adding oil stabiliser (Lucas or Morley's) to my gearbox improved the action a good deal.

Despit my box having been re-built (due to slow undiagnosed oil leek, not thrashing) it was still a bit notchy. I decided to try oil stabiliser firstly before going to the expense of using Redline.

The oil stabiliser label says very worn boxes need 40%/normal oil mix. I tried this firstly and found it too difficult to shift when the box was cold. I re-mixed the formula to 30% and it was much better, but still a bit stiff for the first couple of shifts (I am mixing it with Castrol VMX80). Probably a mix of 20% would be ideal, but I'm leaving it as is cos it feels very smooth once it's warm.

It only costs about $19.00 for a litre, and you only need about half that.

Anyone got any comments on the rights or wrongs of doing this? I mentioned it to my mechanic (Gavin Wood, Autotech) and he had nothing against it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...