Jump to content
SAU Community

Recommended Posts

if u r just pulling the old box out and replacing with a new its just straight forward . drop one out lift other up bolt on and way u go . if u r going to change the clutch at the same time then u have to line the clutch up , if u want to do that let me know and i'll post for u .as long as u know the basic stuff , undo tail shaft all bellhousing bolts including starter , slave , unplug wiring , take the gearstick out , i think that covers it as u have a push clutch it will come out no probs . r33 with pull clutch is a different story .

Link to comment
https://www.sau.com.au/forums/topic/24331-gearboxes/#findComment-519693
Share on other sites

thats what i said before if u want to pull the clutch out ( good idea while the box is down ) to inspect and maybe change it if half or more worn then u have to line it up so u can put the box back up .if u dont line it up the box will never go back .once u have the box down undo all the bolts that hold the clutch assembly and pull the clutch pressure plate off . have a look at the clutch plate for wear and if 1/2 worn u need to get a clutch kit ( new clutch plate , new or rebuild pressure plate , new thrust bearing and a new spiggot bush or bearing ( not sure if ur car has bush or bearing ). i would take the flywheel off and get it machined ( 30-40 $ ). install the spiggot then flywheel ( i always use locktite on the bolts ) then the pressure plate with clutch ( make sure u put the clutch plate the right way )use locktite on the pressure plate bolts . before u do the pressure plate tight u line up the spine of the clutch plate to make sure its in the middle its got to be spot on ( u can buy a tool to do that ) i have old g/box input shafts to line up my clutches . as long as its lining up when u lift the g/box up threre it will go in u just turn the box left to right a little so spline of the shaft doesnt hit the clutch spline and u r sweet .if it doesnt line up it wont go cause the pressure plate presses the clutch plate hard and it wont move . i hope it this helps u , by the way u r lucky it has a push clutch and not a pull one .

as for machining the flywheel have a look if it hasnt got burn marks ( if u drive like a grany it may not ) then dont worry but i always do it .

if got another clutch with the new box that u r instaling check it out if nearly new use it if not dont risk it . u can get a new clutch kit for u r car for 200 - 250 ( stock )

Link to comment
https://www.sau.com.au/forums/topic/24331-gearboxes/#findComment-520639
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car remains in paint jail. I am now pretty convinced that the whole "RB25 Airboxes are kinda limiting to ~300kw" could be a thing. Also saw a good video from Engine Masters: (Sorry for FB link) (https://www.facebook.com/watch/?ref=search&v=761771519471924&external_log_id=c10bcbb6-2c39-4ff3-9240-287e9921fde6&q=Cold Air Considerations) Where they tested Pod Filter sizes and kept adding bends to a LS3 on an Engine Dyno to find if bends caused power loss. It's a good video worth watching - They did lose ~25hp from making an intake which had 3x90's and a 120 degree. They only lost maybe 1hp with a basic 90. I feel that by sealing up my airbox I have: 1) Created the same restriction a stock airbox would have. 2) Created a very convoluted set of intake 'pipes' by forcing all the air through the ducts. So I am pretty confident I'll be going full circle and have a huge hot air intake pod and actually see a benefit. The air does *not* stay hot once it gets flowing, aided by the ducts, and the pod can then pull air from anywhere. All the posts of yore talk about the stock airbox costing 10-15kw at 300kw+ but you know what? I f**king would very much like that 10-15kw and I remember my own pod filter in engine bay experiences. Turns out the GTT Reo and Headlight brackets really don't allow you to mount GTR items, no matter what the internet says. Various brackets have had to be made up to actually make it fit right for the front bar. Also some idiot mounted a 3L Accusump right where the bumper wants to go, so that has had to be 'relocated' To where, I am still not sure, but it's supposedly mounted in the pictures and I can't see it.
    • Sounds like the oil pressure light is wired into the oil temp sensor... As it warms up, resistance on temp sensor reduces, hence more current can flow and the dash light gets brighter.
    • Got the front subframe and suspension in.    
    • If it's cold in summer, then no issue. If it's cutting out every few seconds and you're not reaching your target temp, then there's an issue. One could be the pressure switch and the other issue could be the temp probe inside the evaporator.
×
×
  • Create New...