Jump to content
SAU Community

Recommended Posts

hey guys, im thinking of organising a cruise to newcastle forshore, just seeing how many ppl would be intrested in going.

im at tuggerah so mayb for the central coast ppl we can meet somewere round here.

itll be held on the 15th of november, ( saturday )

thanks :P

Link to comment
https://www.sau.com.au/forums/topic/243579-cruise-to-newcastle/
Share on other sites

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

I think you'll find there's already 2 events planned for the 15th :P

Best bet it to have a look in the events section to see whats coming up and choose a date from there (not trying to discourage you, but 2 things on the same day already may make it hard) then you'll have a better chance of a good turnout

Cheers

Newcaslte foreshore probably isn't a wise choice for a cruise. Sure, you'll get a lot of attention, but there is always police running that strip trying to defect people.

Depending on what the weather is like as well, it'll be hard for a decent sized group of cars to park close to each other. Nobby's beach carpark would be an option I guess, but it is normally packed on a nice day.

Yeh its pretty hard this month to organise a cruise.

Depending on the number of people you want to turn up is very vital..you need time for people to make plans

2 weeks prob won't cut it also there are too many things goin on.

29th or 30th Nov would prob be the best time or even the next week after.

Just a suggestion.

Newcastle is a hotspot for cops, cars are everywhere on Sundays too espescially on a nice day.

Let me know when a set date is.

Cheers.

RJ

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...