Jump to content
SAU Community

Recommended Posts

Hey guys, had a rather strange Issue with my GTR, driving it i had an engine check light come on.

so pulled over turned off car then on again and then continued normaly,.

The proplem came up again, car ran like crap.

Anyway lucky for me i have a power FC with hand controller and i did a sensor switch check, all was noraml untill it happend again.

Bascily it came up with airflower meter 1 as being faulty with low voltage.

Is this a wireing fault or an airflowmeter fault, meaning repalcement needed. ? ?

Can i use the power from the number 2 to power 1?

Number 2 is fine with correct voltage etc..

:blink:

Thanks guys any help is great....

hmmm what?

If one is showing bad voltage, its stuffed.

Or the wiring is... being the plugs are the same, it stands to reason you could swap them to see...

Stuffed yes...but also repairable.

You need adapters etc i believe.

Nismo AFM's are a Z32, in a stock case... so they bolt onto everything you have... plug included.

So they are by far the easiest option and hence most people get Nismo's over Z32's

purchaced some z32 airflow meters today with bosh plugs just need to wire them up. Thanks WAZ

Once installed am i able to slected on the power FC VG30 80mm airflow meters as thats what they are, its at the bottom of the list.

It has 80mm rb25 one as well. Super, then R32 and R33 Normal.

Will i require a tune.

Any info will be handy

Cheers again guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This car has run before on this z32 ecu can get the part number for you, I have tried with no AFM it didn’t change anything, I compression tested today 140-150 across all 6 cylinders, also set fuel pressure to 43psi. The only weird thing was cylinder 1 plug was black and fouled other 5 cylinders were just wet with fuel. Spun cas by hand and confirmed injectors are clicking 
    • Since you came here to ask for help, have you thought about answering our questions, that might help us lead you to why it was skipping, or have you given up on getting advice?
    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
×
×
  • Create New...