Jump to content
SAU Community

Recommended Posts

mroe than likely the voltage level of the battery when connected was too low for teh charger to operate - alot of them have this feature but im not sure why

jump start charge it, then hook up the charger after 20 mins or so.

how did you go with the charger, id just go a yellow top dry cell.

Hmm.. well it finished charging. Will try to put it back later today.

I was hoping to put in a yellow top as you suggested (although I still think $360 for a battery is quite steep), but the battery cables aren't long enough to accomodate a bigger battery, and I'd have to change ther terminal rings to bigger ones as well.

Ground cable connection, which I could possibly replace to accomodate a bigger battery.

M0005.jpg

+ve terminal connection

M0014.jpg

The positive terminal is wired into this power supply thing. Try as I might, I cannot remove it. This is a bummer as it means I am restricted to buying batteries only as high as my old tiny battery, as there is no slack in the wire when the battery is there.

Apart from the +ve and -ve terminals, there is a drain tube of some sort going into the battery

M0009.jpg

which slots into this hole in the battery

M0011.jpg

I have no idea what this is... is this for leaking acid or something? I would have thought the Pitwork battery that Nissan put in the stock GTR would have been a sealed type, and wouldn't need this.

Its normal mate, my gts-t has that wierd hole which u connect to that clear hose and goes under the car. I think it is for acid spillage or something like that.

Got my battery hooked up to a charger now. Thats what u get when the car isnt used for 6 months lol

+ve terminal connection

http://i384.photobucket.com/albums/oo281/mrphatboy/M0014.jpg

The positive terminal is wired into this power supply thing. Try as I might, I cannot remove it. This is a bummer as it means I am restricted to buying batteries only as high as my old tiny battery, as there is no slack in the wire when the battery is there.

It's not actually wired in. Pop the red boot at the bottom there and there should be a nut. Get to it with a socket and you'll be able to get that positive wire out and replace it.

I went to a battery place that wanted to charge me $100 to do it. So I went home and started pulling things apart. I got the positive wire off within minutes. Replaced with cable, eyelets, and new terminal from Jaycar. Cost me about $10 and 20mins of my time.

Yeah that pipe is for leaking battery fluid, if you run a yelow top then you wont need this as they are a sealed bettery.

As for your ground / Power cable as wilch said just pop down to Jaycar to get the parts and do it yourself. While your at it get a nice set of terminals, especialy if your running extra power cables to amps, it would be worthwhile running a couple of extra grounds as well.

The old battery went in and the car starts up! Finally!

Thanks for your help Stokesy. I will keep that in mind when I need to change the battery. That metal plate thing in the boot is a friggin bastard to get out and put back in. Hopefully won't need to do it again soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...