Jump to content
SAU Community

Recommended Posts

ok been talking amongst my mates and we dont know whether they will fit

18x8.5s +17 offset on R33 GTS-t fronts - (im sure the rears will be fine)

what do you guys reckon?

will i have to roll the guards? is it hard? where my front bar hooks up to the quarterpanels (closest to the tyre) is already dodgey because I have ripped the front bar off a few times in the past.

what do you guys think? is there any sort of online calculator that someone has made? :rofl:

cheers

Link to comment
https://www.sau.com.au/forums/topic/244469-will-these-fit-guys/
Share on other sites

I've currently got 18x9" +30 on the front of mine and they fit perfect... yours will sit almost the same (less width but more offset) you will need to be running some neg camber tho... around 1.5º should do it... and maybe a 225 tire for added clearance (I run 235's)

I have 18x9" +30 on the front of mine too. Fills the guards nicely.. I'm using 235s

I assume +17 will just stick out a little more, but your rims will be half an inch thinner.

I reckon they'll fit easy, unless I don't know what I'm waffling on about. (I don't)

I have 18x9" +30 on the front of mine too. Fills the guards nicely.. I'm using 235s

I assume +17 will just stick out a little more, but your rims will be half an inch thinner.

I reckon they'll fit easy, unless I don't know what I'm waffling on about. (I don't)

yeh im hoping i can get away with stretching a tyre over them - im going to full lock the car later today and see where it is closest... i dont know what camber i have atm

yeh im hoping i can get away with stretching a tyre over them - im going to full lock the car later today and see where it is closest... i dont know what camber i have atm

so if your offset is 30 and mine is 17 that means mine should poke out 13mm more than yours IF we had the same width rim but considering mine is .5 of an inch skinnier and there are 25.4mm in an inch that means mine are 12.7mm skinnier

so can someone confirm that mine (by my math - it might be wrong) is going to poke out .3mm more than your rims NickR33... is that right?

hehe thanks

Your maths is almost right but you have to realise that half of that 12.7mm is going to be on the inside of the rim. So your rim will be 6.35mm further in due to width but 13mm further out due to offset.

Net effect is 5.65mm further out. If you run a skinnier tyre and theres no issues with rubbing then it should be fine...

will definately need to pump the guards for legal fit - plus your track will be illegal (but bloody close) which should only be a problem if you go over the pits and they measure them.

You will probably need to run a 215 tyre or the tyres may rub - or you pump extra and remove the inner guard (plastic) or fit glass wider guards.

Getting similar offset on the rear will require rather more massaging of the guards than the fronts (just in case you were thinking of going down that path)

I believe Tech9tyres can pump guards for you if your not up to it, they used to a while back.

Edited by Steve
will definately need to pump the guards for legal fit - plus your track will be illegal (but bloody close) which should only be a problem if you go over the pits and they measure them.

You will probably need to run a 215 tyre or the tyres may rub - or you pump extra and remove the inner guard (plastic) or fit glass wider guards.

Getting similar offset on the rear will require rather more massaging of the guards than the fronts (just in case you were thinking of going down that path)

I believe Tech9tyres can pump guards for you if your not up to it, they used to a while back.

rears are 18x9.5 at +25

thanks for the advice bud

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...