Jump to content
SAU Community

Recommended Posts

hi guys & girls

i have the following for sale. preffer pick up, but i can send if its worth it to you.

r34 triple gauge cluster (gauges only, no surround cover) used condition $40

r34 fuel pressure regulator. used condition $10

r34 traction control throttle body (only good for tcs motor, body is hacked up) $10

r34 air flow meter (pink sticker, good for pod filter only as square section has been cut off) used $50

r34 timing cover used $30

r34 stock turbo (only good for housings front +rear...no shaft/blades) $30

r34 stock rubber intake tube. used. $10

R34 turbo heat sheild. used. $10

r34 wastegate modified braket. used. $10

r34 stock fuel rail and injectors. used. $90

r34 amber front blinkers. used. $20

r34 amber side blinkers. used. $10

r34 bare intake plenum top and bottom sections. used. $100

r33 6 stock injectors (one missing the plastic at bottom, see pic). used. $40

r33 amber side blinkers. used. $10

pick up is Dharruk just near rootyhill

i need this stuff gone, if not sold here it will be put on ebay, so all offers considered.

Justin

0408 589 335

post-1416-1226743255_thumb.jpg

post-1416-1226743297_thumb.jpg

post-1416-1226743333_thumb.jpg

post-1416-1226743354_thumb.jpg

post-1416-1226743374_thumb.jpg

post-1416-1226743403_thumb.jpg

post-1416-1226743443_thumb.jpg

post-1416-1226743470_thumb.jpg

post-1416-1226743498_thumb.jpg

post-1416-1226743521_thumb.jpg

post-1416-1226743545_thumb.jpg

post-1416-1226743567_thumb.jpg

post-1416-1226743586_thumb.jpg

post-1416-1226743603_thumb.jpg

post-1416-1226743630_thumb.jpg

post-1416-1226743648_thumb.jpg

Shotgun the...

-fuel p reg

-turbo

-intake pipe

-heat shield

-wastegate

-and 34 fuel rail + injectors

Message and pm sent!

Payment made!

Thankyou

Edited by chriz
  • 5 months later...
Any chance of the TCS motor still available ?

yes its still available, as stated its good for the tcs motor only, the round pipe section has been cut.

Thanks

Justin

turbo still available by any chance?

thanks

no sorry

turbo sold

turbo heat shield sold

wastegate actuator sold

r33 injectors sold

r34 fuel rail+injectors sold

turbo rubber intake tube sold

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...