Jump to content
SAU Community

Recommended Posts

Hey guys, I'm looking at buying a late model R33 GTS4 and doing a RB26 conversion. Has anyone does this before?

Just wanna know what I'll have to change in the drive line.. like Gear box etc..

Just curious to know if the R33 GTS'4 use the ATTESA system like R33 GTRs?

thanks guys..

Link to comment
https://www.sau.com.au/forums/topic/245211-late-model-r33-gts4-with-rb26/
Share on other sites

Yes. They use the same ATTESSA as GTR.

Its not the exact same gearbox as GTR (shorter gears) but stronger than GTS

You will have to upgrade fuel pump to match the 26's needs.

Other than that. Its all very straight forward

So the Drive line is strong enough as it is? Dont need to upgrade beside gear box clutch?

So if i was to buy a late Mode R33 GTR half cut... with Box and ECU loom.. etc.. all that stuff..

Everything will bolt in fine?

all depends on your drive, if you're dumping the clutch from the rev limiter constantly and side stepping the clutch during changes then don't expect anything to last long.

The car will be driven to its limits on the track... But on the street just the usual burst here and there...

Should be alright I'm assuming...

i hate to be a smart arse, but nissan did it. They took a gts4 and put in a rb26 a well as giving it a wide body kit and some more guages, among other things.

They called it the skyline gtr.

Seriously though, why do you want to go down this path? Cost? how much do you think you will save? Something different perhaps? Found a cheap gts4? Doing it for a challenge or hobbie? etc...

gearbox will be fine

rear diff wont be

its not a small job, like any conversion, its gonna cost quite a few $$$.

Unless you were getting the gts4 really cheap, i would sit down and do the math and see how much you're going to spend. With the price of r33 gtr's these days i think you'll find that it doesnt work out that much more to get the real deal.

But its all apart of the fun, if this is a project car go do it and you'll learn a whole lot, but if you want it as a daily save up that little extra and just get the gtr

  • 2 months later...
I bet you will be half way thru the conversion and say to yourself "i should have just bought a bloody GTR"

If you do complete the GTS4 RB26 conversion, it still will never be a GTR.

Never want it to be a GTR.. just a street sleeper.

Im going down this same path with my R34 GT-four. Hoping to bolt a RB26/30 into it later this year. Will let you know how i go. I'll make a project build thread sometime in the year.

I did it with my R32, now i have a 316kw GTS4. Would have been heaps cheaper to just buy a GTR but that depend if ya gonna do the work yourself. The look on peoples faces is classic when you blow them away at the lights :)

Edited by DSTROY
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
×
×
  • Create New...