Jump to content
SAU Community

Recommended Posts

$26, 000

Nissan Skyline R32 GTR

*have invoice for most of the work done

Engine

HKS step1 camshafts ( 264 intake / 272 exhaust )

HKS adjustable camgears

HKS inlet manifold gasket

CP Pistons

SplitFire coil packs

Gates timing belt

cometic head gasket

custom P20 tool steel heat treated billet CNC machined oil pump

R33 RB26 crank shaft

external oil return lines from cylinder head to sump

Garrett GT35R Ball Bearing turbo with Anti Surge compressor housing and .78 divided (twin scroll) exhaust housing

Garrett Turbo Heat bag for turbo exhaust housing

TiAL 44mm external wastegate

screamer pipe

custom steampipe Twin Scroll Manifold to suit divided exhaust housing

custom dump pipe + front pipe

hi flow 3inch cat

X force cat back exhaust system

115mm intercooler

custom aluminum intercooler piping

custom intake pipe

custom air box

greddy blow of valve

custom catch can

N1 water pump

aluminium radiator

Fuel System

SARD fuel reg

SARD 800cc injectors

Bosch 023 fuel pump

Management

Power FC D jetro

Power FC commander

Suspension and Brakes

cusco coil overs with swift springs

hicas lock bar

EndLess VN front pads

EndLess brake fluid

DriveTrain

HKS triple plate clutch

HKS fly wheel

Interior

Recaro SR3 Passenger & Driver side

Blitz ID3 boost controller

Gizzmo shift light

Defi style boost gauge

Greddy remote control boost switch

Exterior

CR KAI 18 X 9.5 +12 BRONZE

Nismo side skirts and Nismo rear pods

POWER: 360kw @ 19psi

dyno2.jpg

R32GTR.jpg

DSC00385.jpg

Link to comment
https://www.sau.com.au/forums/topic/246811-r32-gtr-26/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...