Jump to content
SAU Community

Compression Results On 34gtt

1R34SON

By 1R34SON,
in General Automotive Discussion

 Share

Recommended Posts

1R34SON Proficient

1R34SON

Posted
Posted

Lookin to buy a car and had a compression test done by performance place and just wondering if anyone can give me some advice. ill update the exact results for each cylinder later but on average no higher than 170 and no lower than 150, i think was somethin like 170, 170, 150, 160, 155, 150

like i said ill update bit later, but thats basically what i remember? was told its ok, then told its not any help please????

Thankyou!!

Link to comment
https://www.sau.com.au/forums/topic/247656-compression-results-on-34gtt/
Share on other sites
Pattygtst Veteran

Pattygtst

Posted
Posted

You get different readings depending on the battery and a few other components. I believe 150 is standard but the higher the better they say.

Of course they must be consistent with each other.

If there not identical to each other move on to another car until you find one that is.

You want it to be spot on

Pattygtst Veteran

Pattygtst

Posted
Posted

the other thing is you really need a leak down test also.

When i had my 100km service the compression was 170 170 170 170 60 65, since the car is pulling max power for the mods i was like wtf

Turns out i just had a heap of carbon build up in the intake.

Test after was 170 170 170 170 170 170

1R34SON Proficient

1R34SON

Posted
  • Author
Posted (edited)

Ok results were As follows:

CYLINDER 1- 170PSI

CYLINDER 2- 170PSI

CYLINDER 3- 160PSI

CYLINDER 4- 150PSI

CYLINDER 5- 155PSI

CYLINDER 6- 160PSI

Guy from the workshop said car runs smooth as a babys behind. and really seems like the guy doesnt thrash it, middle aged and very particular owner and mechanic said car is very well looked after. then again u never kno what happens in japan. Im gona ask for a leak down test I think to be sure. what u think?

Edited by 1R34SON
turbo_brian Community Regular

turbo_brian

Posted
Posted

When I bought my car, I had a clause on there, which was I can return the car if my mechanics testing showed the engine was not in good condition.

Did a dry compression test: 1 - 176, 2 - 175, 3 - 177, 4 - 176 , 5 - 177, 6 - 176

Did a wet compression test: 1 - 177, 2 - 177, 3 - 176, 4 - 177, 5 - 178, 6 - 178

The minimal difference in figures means that it was great compression to start with, and after using some oil to further seal the rings, the figures where almost the same (there is a variance in or 3 - 5 psi in the gauge I used). Considering the figures where almost identical, it means there is no pressure loss on the rings, meaning any pressure loss is in the valves.

a Leak-down test revealed the pistons hold very good pressure, meaning the valves are not loosing pressure, and the engine is in good condition.

Did a radiator pressure test as well, revealed no issues, did an intake pressure test, no boost leaks or other leaks,so I rang the previous owner and told him to go nuts with the money, I wasn't disappointed with the tests at all.

I later found out from a relative of the previous owner that the engine had blown, and was completely rebuilt from the ground up, forged pistons, rods, balanced crank, all the oil mods to the head, sump baffles, N1 turbochargers, etc. The works has been put into that engine to make it bullet-proof (as bullet proof as an RB26 will get), but then he had to sell for family reasons.

If you get a good RB engine, and you let them warm up before revving them and thrashing them, keep good oil to them, and dont rev them over 7,000rpm (unopened), the engine should be good for a lengthy life.

It's the other bits you need to worry about, gearbox, diff, suspension, rust through the body, but someone who knows cars will be able to pick if they have been in an accident, or if they are riddled with car-cancer.

My only advise: Dont fall in love with a car while looking, treat them all as damaged stock until you find the perfect one, and once you have purchased it, you can fall in love. (I fell in love with a 180sx yrs ago, wanted it no matter what so I wasn't maticulous in checking it out. Later found a 1 inch rust spot, took the screwdriver to it to brake all the rust out before welding a plate to the car, and the hole was 1 inch, but the rust through the panel was 1 foot 2 inches, it was HUGE!!!).

B.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Again - as stated earlier... its the % difference not the actual numbers more than anything.

Obviously if it goes

160 150 155 160 150 80

Then you have a problem, but if they are all near enough to the same number, its fine and a good result.

If you want a much better TEST - Leak Down test is the one your after

1R34SON Proficient

1R34SON

Posted
  • Author
Posted
Again - as stated earlier... its the % difference not the actual numbers more than anything.

Obviously if it goes

160 150 155 160 150 80

Then you have a problem, but if they are all near enough to the same number, its fine and a good result.

If you want a much better TEST - Leak Down test is the one your after

spoke to a guy from a turbo engine tuning workshop and told me this same thing ^

he said that numbers will usually vary. and as long one isnt out by heaps or under 150 its fine. cheers all!

Kinks Grand Master

Kinks

Posted
Posted
When I popped my stocker, it went:

Cyl 1/ 0

Cyl 2/ 75

Cyl 3/ 150

Cyl 4/ 150

Cyl 5/ 150

Cyl 6/ 150

See if you can guess which piston had a broken ringland and which had lost ring tension.

I'm guessing Cyl 2 had a broken ring land and your ring lost tension when you realised the motor needed a rebuild :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...