Jump to content
SAU Community

Recommended Posts

hey just wondering if flutter is bad for the car and if so what damage will i be causing the engine turbo etc. the flutter effect is when the small breather hose is disconnected off the stock BOV and bloked off both ends....

please add in your 2 cent :spank:

Link to comment
https://www.sau.com.au/forums/topic/247829-flutter/
Share on other sites

Ask any VL driver, flutter is SIK BRO!!!

Flutter it the sound made by air pressure that does not release when you close off the throttle body (usually because of a lack of BOV). The sound is the air rushing back from the throttle to the blades of the turbo, and the air gets chopped up.

There IS pressure on this, and it does cause undue pressures on the turbocharger blades, possibly causing minor damage, but my personal thoughts are that unless there is already issues with the turbocharger(s) or the units are old, you shouldn't have much trouble.

B.

Link to comment
https://www.sau.com.au/forums/topic/247829-flutter/#findComment-4302609
Share on other sites

In my R31, flutter was so 1989 :(

Sounded awesome, and that car ran beautifully with no BOV. However, my 33 does not like its BOV being blocked off, driveability suffers. The ECU must be more sensitive to the intake tuning.

Myth that no BOV will kill your turbo is BS. My 31 ran 1 bar for 3 years and never had an issue.

Link to comment
https://www.sau.com.au/forums/topic/247829-flutter/#findComment-4303336
Share on other sites

In my R31, flutter was so 1989 :)

Sounded awesome, and that car ran beautifully with no BOV. However, my 33 does not like its BOV being blocked off, driveability suffers. The ECU must be more sensitive to the intake tuning.

Myth that no BOV will kill your turbo is BS. My 31 ran 1 bar for 3 years and never had an issue.

Edited by iamhe77
Link to comment
https://www.sau.com.au/forums/topic/247829-flutter/#findComment-4305859
Share on other sites

Lot of info here about flutter.

http://www.nissansilvia.com/forums/index.php?showtopic=28060

By removing the vacuum hose ontop, the bov can still vent due to the high pressure air pushing the piston in the bov up.

Best method is to put a metal plate between the bov and the cross-over pipe.

Expect the car to stall when coming to a stop and becoming real sluggish. The stock ecu hates flutter and will make the car shitty to drive.

Link to comment
https://www.sau.com.au/forums/topic/247829-flutter/#findComment-4306018
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...