Jump to content
SAU Community

Recommended Posts

I'm guessing the 2871 would be a more appropriate sizing for 220-250kw and ultimately quicker spooling and response?

Less torque but more consistent over the power band.

Smoother power delivery slightly but holds about the same up to redline!

  • 3 weeks later...
  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

hey, ive had my NEW hypergear hiflowed turbo on my r33 for 4days..

just sent my stock rear exhaust housing (snail) to the east...

they hypergear fitted a ATR28 G2 core and new front compressor housing(polished!! :thumbsup: ) ..

and a 14psi actuator..

all for $925 including shipping...

done bout 200ish k's...

and its goning well...

still running it in...so yeah..

but seem alot better than stock..

and it boosts alot better too, from what boost levels ive hit....

i would recommend this to any r33 driver that requires a new turbo...

evan if car is fairly stock...e.g: ecu/afm/injectors...

theres a few modifications u gotta do to make it fit..

like the oil feed line...and the inlet & outlet on the compressor housing..

but other than that its worth the upgrade...

Ok here's a initial running in result from a high flow using a ATR28SS. car had boost controller issues so peek boost of 12psi and dropped to 9psi. made 201rwkws with almost identical response to stock Ceramic BB turbo. Car will come back to do a run power tune once done 1000KMs, expecting even better response with about 250rwkws..

RB25Neo, Stock ceramic BB turbo vs ATR28SS. The car was dynoed before turbo upgrade.

atr28ssRB25200kw.jpg

atr28ssRB25200kwboost.jpg

Edited by hypergear
  • 2 weeks later...

could you please provide me with a price, delivery into Adelaide, for a Hypergear ATR28G3(450HP) profile in Ball-Bearing

would like it to be highflowed to the maximum to front / rear housings, to suit a RB25det

cheers, much appreciated

could you please provide me with a price, delivery into Adelaide, for a Hypergear ATR28G3(450HP) profile in Ball-Bearing

would like it to be highflowed to the maximum to front / rear housings, to suit a RB25det

cheers, much appreciated

would also like a quote on this. emphasis on ball bearing cartridge not thrust bearing. with supplying own r33 standard turbo

delivery to brisbane aswell

Thankyou :thumbsup:

Edited by stenve

Please check PMs. Also some bad news on the Garrett BB CHRAs. Garrett fliped their whole sale price up by 33% over night on popular CHRA models. lol. So now its going to cost 33% using Garrett GT CHRAs.

Edited by hypergear

i had a tr43 on my rb20det i couldnt adjust the acuator as it was hitting the rear housing of the turbo. so it was boosting to 20psi, apart from that it lasted oh say about 2 weeks befor it shit itself there f*kin shit if your gunna buy a turbo spend the money.

Rowan unless this turbo was made back in 2006 or a similar looks alike this sort of thing do not happen to our TR43s. Our internal gates in them has been specifically designed and tested on RB25s they do not spike, also Our rear housing never hit, They are running the same diameter as a .58 R34 rear housing. and using the exact same diameter comp housing as a S14. There is no chance it will hit.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...