Jump to content
SAU Community

Car Won't Start

ben_wha

By ben_wha,
in Western Australia

 Share

Recommended Posts

ben_wha Contributor

ben_wha

Posted
Posted

Ok. So I was driving on Saturday, and when I gave it a bit (under full boost = 10psi) it would hit a wall kind of like boost cut at 4500rpm for 5 secs then kick into boost again.

Checked over a few things that I thought could be the problem.

1: cleaned afm and plug.

2: tightened intercooler piping and checked for boost leaks.

Nothing worked

Was running and driving fine apart from when I put my foot down.

Then this morning I went to start it up and it wouldn't kick over. So I got a new battery since the one I had was a lil old, put it in and still no dice

All the belts are moving and its just on the point where it wants to kick over, which makes me think it could be the starter motor??

Car was also recently tuned.

Car: Silvia

Engine: Rb25det

Mods include, splitfire coilpacks, turbo back zorst, Apexi avcr, apexi safc, platinum plugs, intercooler, brass button clutch, nothing major.

Any suggestions would be great.

cheers, Ben

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/
Share on other sites
NA_Goodness Grand Master

NA_Goodness

Posted
Posted

So it's cranking, just not starting? If that's the case, it wouldn't be starter motor. To eliminate that, try jump starting it. If it starts, that'll be the problem. It still would explain the problems under boost.

I would have said coil packs, but you've said their spitfires so that wouldn't be it. Have you had any work done to the car recently?

Check the ignotion system. Is the car getting spark? Is it getting fuel? Are there any plugs that have fallen off? All the vacuum lines attached? I'd check all these first, and then take it to a mechanic.

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4309946
Share on other sites
Dani Boi Grand Master

Dani Boi

Posted
Posted

You need air, fuel and spark to start an engine. Seeming as though you havent listed an aftermarket fuel pump (possibly meaning your still running the 15 year old standard one) under mods that would be the first thing I'll be checking.

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4309984
Share on other sites
R33_NICK Community Regular

R33_NICK

Posted
Posted

try checking the coilpack wiring loom as this can deteriorate overtime which will also cause the car to not start apparently some people who replaced the coilpacks didnt realise that while doing it they might have damaged the wiring as overtime heat caused the wiring to be crispy and would crack easily

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4311013
Share on other sites
ben_wha Contributor

ben_wha

Posted
  • Author
Posted

Changed the ECU and ignitor module yesterday, neither worked, there was no spark at all. So the problem lies between the module and ECU (as said above, in the harness somewhere).

My thoughts, it could be the resistor?

IS anyone an auto electrician on here or know someone that can come to me as the car doesn't go. For cash :P

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4311519
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...