Jump to content
SAU Community

Recommended Posts

Hi guys,

Just thought I would throw in my 2c if that's ok:)

turbo cars are fitted with bovs that plumb back - this is something the manufacturer does, and for good reason (another story)

atmo BOV vent crank case gasses to the atmosphere - this is in direct contradtion of road traffic acts australia wide, and it also contravenes EPA reguations.

It took me a while to work out why atmo BOVs are illegal, until I was reading ADRs with regard to crank case gasses.

All vehicles manufactured after 197? (from memory) must burn crank case gasses through the cylinders as part of emissions control - this is where the problem lies, as under boost crank case gasses go into the intake after the afm and before the turbo (which is why we fit catch cans). Once we take out foot off the accelerator, those gasses vent to atmo.

Hope that clarifies.

As for noise, the only regulations I could find were on vehicle exhaust noise, as for removing a 'turbo whistle' OMFG how can you remove something that doesnt exist - should take him to court purely on the principle - like to see the copper produce a dictionary (or any other legitimate) definition of a 'turbo whistle'. If a defect notice is a legal document, shouldnt the issuing copper be under some sort of requirement to get his terminology right?

Should get a statement off a mechanic to the effect that there is no such thing as a turbo whistle, then go see the guys supervisor and make a complaint that you wasted time trying to remove something that doesnt exist:)

CRANK CASE GASSES are different form your bov gasses.

catch cans are used to stop- the amount of shitty blow by in your engine. mostly used for ****ed cars, or crazy high performance cars. bov's vent air that has come from your air filter, thru your turbo then thru the intercooler to your pipes.

there must be different laws in SA. as this is the Queensland section.

now listen. Atmo BOV are legal.so long as they comply to the noise and polution levels.

Where do the crank case gasses go when under boost?

All cars create blow by, whether only a little or alot. If you have a look at the two connectors on top of the rocker cover you will see that they go to the intake, after the AFM, as under boost the gasses cannot go into the plenum for obvious reasons, which is prevented by the PCV (positive crankcase ventilation) valve.

If the gasses did not go into the intake, or were vented to atmosphere, the crankcase could pressurise and cause all sorts of problems (like blowing gaskets and seals - not pretty)

It was only in the early seventies that cars started being required to comply with emissions standards, and the gasses could not longer be allowed to vent to atmosphere.

If the rest of you emissions control is correctly plumbed up, there is no physical way you can stop some crank case gasses getting into the charge air. It is this charge air that vents when the BOV lifts, hence atmo is not street legal.

The requirements for cars to comply with emissions standards are the same in every state.

  • 15 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes I can see how that would put you off HFM, especially with the price of good quality brake fluid. From what I understand it as you say the BM50 is the standard BMC for a R32 GTR, I must admit I would like to go far a Genuine Nissan BM57, but lack of cash prevents that at present. With the price being so close between the genuine BM50 and BM57 a BM57 New it seems a better choice as you gain that 1/16 bore size with the BM57, I would be interested in how much difference you feel with the BM57 fitted. I am going to take SteveL's advice in the short term and see how much actually comes out of that proportioning valve vent and save up for the Genuine Nissan part. Thanks for clarifying the HFM failure
    • Thanks mate. I just got the post inspection 1/2 done from state roads when the starter motor packed up, either that or the car alarm system is having trouble.  OEM part number 23300-AA112.
    • Hi, I though I was coming to an end in finding a replacement starter motor for a rb25de neo. I came across a starter motor from Taarks and a message below stating: Direct fit. 11 Tooth count. All below part numbers have been superseded to 11 teeth. Can some body shed some light on going from 8 teeth to 11 teeth apart from 36-month / 25,000 km warranty for passenger vehicles to 12 Month Warranty. Compatible with the following Nissan part numbers: 23300-20P00 23300-20P01 23300-20P05 23300-20P10 23300-20P11 23300-AA111 23300-AA112 23300-AA300 23300-08U10 23300-08U11 23300-08U15  
    • Low battery? Maybe check capacity? I know first-hand, on BMWs if your battery drops below 80% capacity, it starts causing strange issues.
    • 8.5 +37 = should fit rear, but I think it'll hit on front. What you want is low 30s/high 20's front, mid 30's rear. That 17" screenshot you posted looks good, I'd run it on my R32 (but that's long dead now). For tyre sizes, my rule of thumb is: 8': 235, 9": 255. But that's just my opinion. Nismo sizes: 18x8.5+35/18x9.5+38 is a good starting point.
×
×
  • Create New...