Jump to content
SAU Community

Recommended Posts

  • Replies 155
  • Created
  • Last Reply

Top Posters In This Topic

Yes, you can use the wiring for the stock boost solenoid. Mine has been wired up with spade connectors straight into the stock boost solenoid plug :(

You will need to change the way the tubes to the mac valve are set up, though.

well ive only got to choose from 1 black and 1 white wire to connect the wires from the MAC valve (which both wires are black). i dont know which one to connect to which. the wiring diagram only had the colours that come from the ecu which are LG and L/W.

and i still dont know which wires from the mac valve are + and -

I just went and had a look at mine for you. Both wires on the Mac valve are black, but it looks like one has writing on it. I also saw '---', so I guess that one is the negative. The stock BC connector is a rectangle shape with the connectors in a T sort of layout. The connector that is at one end of the rectangle connector is the negative. The one that runs down the centre of the 'rectangle' is the positive. I hope that makes sense.

OK, well there ya go then. That would explain why the wires are both black :D

yeah it confused me at first.. just like injectors.. they don't have + or -

you learn something every day ;) .. dunno what i have learnt yet though :)

yeah it confused me at first.. just injectors.. they don't have + or -

you learn something every day :D .. dunno what i have learnt yet though ;)

Yes you have...

That DiRT is a tightass and wont spend coin on a wideband

Yes you have...

That DiRT is a tightass and wont spend coin on a wideband

If i am tuning it then you are going to have to have a wideband sensor. Simple.

Anthony, get him to pull the one out of your car, then he can put it back when your done?

No.

I win. he purchased one :D I want to setup Open Loop correction on his car.. big $$ engine would be good to have some insurance when he is at power cruise

his o2 sensor is more in the front half than the rear end doof :D

Anthony would you mind PM'ing me with a basic run down of setting up antilag and cyclic idle. Did the fuel map need to be changed at all?

Edited by TiTAN
good thing I don't tune my own car then...

either way... the heart-break is still there...

hey ive tuned your car!!.. Twice! Stop your whinging!

& No can do Titan.. you got stock turbo.. i am guessing it would break on your first anti lag.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...