Jump to content
SAU Community

Recommended Posts

I have made the decision to sell off my R32 GTR

The car does not get used much anymore and the rego is just running out without being used. With another dedicated racecar nearing completion it will be used even less next year.

The base car is a 90 model R32 GTR Originaly gunmetal grey.

Engine mods

Engine was rebuilt 2,500Km's ago.

New R33 crank shaft

- Standard bearing sizes

- Fully balanced with clutch and harmonic balancer fitted

- Grub screwed oil galleries

- Modified oil galleries (specific details available to purchaser)

Original 05u block

- Was cleaned, sonic tested, tunnel aligned and honed.

- Internal modifications to assist oil return to sump (specifics available again)

- Enlarged oil return galleries from head to sump

- Oil restrictor fitted

- Modified coolant passages

Factory R33 N1 rods

- Were from an unstarted crate engine

- Fitted with new ARP rod studs and nuts.

Factory N1 pistons

- Were all equally weighed (specific weights to purchaser)

- Fitted with new rings

- From same engine as the rods

Original Head

- Cleaned, decked valves cut and guides replaced

- New stem seals and all spring seat pressures set

- After market Graphite head gasket

- JJR adjustable cam gears and Clear cover

- Mild port work was done to the head when it was apart, nothing major but some casting irreglarities were cleaned up and was flow benched to ensure everything was even and equal.

Turbos are believed to be steel wheel direct replacements

Has an intank 040 pump fitted

Basicaly the engine was blueprinted and assembled, so squish heights etc were all checked, and machined to acheive tolerances required. Its using the same clearances as our race engines but without the exotic pistons/rods/crank etc.

The builder is more than happy to put purchasers in contact with the machinist who did all the pre assembly work to verify exactly whats in it and how it was built.

2x 3/4 inch custom made front pipes (formerly made for the race car)

90mm exhaust from cat back

Extreme heavy duty button clutch

Nismo Slave cylinder

Transfer case was repaired/overhauled 1000Km's ago

Blitz ID3 boost controller

Custom oil catch can system

Suspension- Apexi shocks and Eibach Springs

- Nismo lower rear control arms

- Nismo upper rear control arms

- Nismo Front castor rods

- Cusco upper front camber arms

- Replaced sway bar bushes and links

Its currently set-up with spring rates to suit semi slicks and does handle very nicely on the track.

The body was resprayed last year in a brilliant white. Inside and out paint job done by exclusive colours. Has a N1 rear boot lip and bonnet lip fitted.

Paint work is still immaculate

Comes with Enkei 17 by 9.5 inch rims with decent tires.

Brakes - Callipers were all overhauled with new genuine nissan seals at the beginning of 2008.

- DBA 4000 series slotted front rotors

- Unknown slotted rear rotors

- Bendix ultimate rear pads

- TRW lucas front pads

- Master cylinder recently had new seals fitted as well (mid 2008)

The interior is all in great condition but the seats have the usual bolstering wear on them.

Car recently competed in the NSW dutton rally and held its own very well without missing a beat.

Its completed in club level super sprint championship in 2008 as well as many a track days.

With a good driver it has achieved - wakefield park 1.08.20

- oran park south 49.45

- oran park GP 1.20.10

All of which were done on average Advan A048 tires.

I'm asking $20,000 for it and not open to any form of trade.

May be negotiable if it's going to a good home.

Located in Sydney

Contact 0404 832 620 After 5:30pm weekdays

Here are a few photos of it, I can provide interior and engine bay photos if serious interest is had as the car is currently in storage.

post-8051-1229597160_thumb.jpg

post-8051-1229597122_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/249424-r32-gtr-white-with-mods/
Share on other sites

It has a Apexi Power Fc

On road has never been over 1bar boost and about 280kws at the wheels

Eibach springs I can run different combos but currently it has 8 fronts and 6.5 at rears.

If you want anymore info or photos give me a call :banana:

Contact Jess or Brad 0404 832 620 After 5:30pm

I have made the decision to sell off my R32 GTR

The car does not get used much anymore and the rego is just running out without being used. With another dedicated racecar nearing completion it will be used even less next year.

The base car is a 90 model R32 GTR Originaly gunmetal grey.

Engine mods

Engine was rebuilt 2,500Km's ago.

New R33 crank shaft

- Standard bearing sizes

- Fully balanced with clutch and harmonic balancer fitted

- Grub screwed oil galleries

- Modified oil galleries (specific details available to purchaser)

Original 05u block

- Was cleaned, sonic tested, tunnel aligned and honed.

- Internal modifications to assist oil return to sump (specifics available again)

- Enlarged oil return galleries from head to sump

- Oil restrictor fitted

- Modified coolant passages

Factory R33 N1 rods

- Were from an unstarted crate engine

- Fitted with new ARP rod studs and nuts.

Factory N1 pistons

- Were all equally weighed (specific weights to purchaser)

- Fitted with new rings

- From same engine as the rods

Original Head

- Cleaned, decked valves cut and guides replaced

- New stem seals and all spring seat pressures set

- After market Graphite head gasket

- JJR adjustable cam gears and Clear cover

- Mild port work was done to the head when it was apart, nothing major but some casting irreglarities were cleaned up and was flow benched to ensure everything was even and equal.

Turbos are believed to be steel wheel direct replacements

Has an intank 040 pump fitted

Basicaly the engine was blueprinted and assembled, so squish heights etc were all checked, and machined to acheive tolerances required. Its using the same clearances as our race engines but without the exotic pistons/rods/crank etc.

The builder is more than happy to put purchasers in contact with the machinist who did all the pre assembly work to verify exactly whats in it and how it was built.

2x 3/4 inch custom made front pipes (formerly made for the race car)

90mm exhaust from cat back

Extreme heavy duty button clutch

Nismo Slave cylinder

Transfer case was repaired/overhauled 1000Km's ago

Blitz ID3 boost controller

Custom oil catch can system

Suspension- Apexi shocks and Eibach Springs

- Nismo lower rear control arms

- Nismo upper rear control arms

- Nismo Front castor rods

- Cusco upper front camber arms

- Replaced sway bar bushes and links

Its currently set-up with spring rates to suit semi slicks and does handle very nicely on the track.

The body was resprayed last year in a brilliant white. Inside and out paint job done by exclusive colours. Has a N1 rear boot lip and bonnet lip fitted.

Paint work is still immaculate

Comes with Enkei 17 by 9.5 inch rims with decent tires.

Brakes - Callipers were all overhauled with new genuine nissan seals at the beginning of 2008.

- DBA 4000 series slotted front rotors

- Unknown slotted rear rotors

- Bendix ultimate rear pads

- TRW lucas front pads

- Master cylinder recently had new seals fitted as well (mid 2008)

The interior is all in great condition but the seats have the usual bolstering wear on them.

Car recently competed in the NSW dutton rally and held its own very well without missing a beat.

Its completed in club level super sprint championship in 2008 as well as many a track days.

With a good driver it has achieved - wakefield park 1.08.20

- oran park south 49.45

- oran park GP 1.20.10

All of which were done on average Advan A048 tires.

I'm asking $20,000 for it and not open to any form of trade.

May be negotiable if it's going to a good home.

Located in Sydney

Contact 0404 832 620 After 5:30pm weekdays

Here are a few photos of it, I can provide interior and engine bay photos if serious interest is had as the car is currently in storage.

post-8051-1229597160_thumb.jpg

post-8051-1229597122_thumb.jpg

Hi how are you? I saw this Gtr the other night and i sent you a text message the other day but i got no reply... I am wondering is this car still for sale? Could u send some pics of the interior if possible to [email protected]

Thanks :)

Hi how are you? I saw this Gtr the other night and i sent you a text message the other day but i got no reply... I am wondering is this car still for sale? Could u send some pics of the interior if possible to [email protected]

Thanks :D

Sorry I dont have any pictures of the interior currently and the car is in storage.

Only interested in serious buyers if your genuine buyer wouldn't you prefer to organise an inspection?

If i had the cash i would buy it off you right now Jess.

Good luck with the sale. Thinks about selling the 34!!!

Aww and I would sell it to you cause I know it would be going to a good home!!

Cheers..I think you need a change like me :cool:

Sorry I dont have any pictures of the interior currently and the car is in storage.

Only interested in serious buyers if your genuine buyer wouldn't you prefer to organise an inspection?

Oh ok thats cool i am genuinely interested in the car and would love to see the car its just i work 6 days a week and its hard for me to get a bit of time to myself hence why i asked if u had any interior pictures...

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
    • To be fair it's the other way around. 300kw is boring in a modern Golf or BMW. They are so competent / well-engineered / devoid of emotion that you have to go stupid fast to feel anything. Whereas the <300kw RB still makes all the right noises and it feels good to drive. Can pull off at the lights with the turbo whooshing and the blow-off pssshing and feel like the coolest kid on the block. Just don't look to the side where you'll see the bored housewifes in their shitbox Yaris/Corolla/Camry that kept up because you didn't go fast at all
    • 300kW is so boring in a Skyline, you'll get spanked by someone's mum's Golf with Alibaba pipes, and an email tune.
×
×
  • Create New...