Jump to content
SAU Community

Recommended Posts

ok so i'll tell the story later but i got done good in mascot last ngiht....it was quite funny all up.

anyway one of my 5 defects is that my battery is not in a 'sealed yet vented enclusure'!

does anyone know what that is and is it standard for a R33??? my car never got complied with a box for the bettery in the boot???

also what is the rolling diameter of a stock R33 Gtst's wheels?

more details of this funny story to come...

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/
Share on other sites

the usual "if in doubt hand it out" mentality was obviously in play here.

what he is saying is this

battery's which aren't sealed units that are mounted i the car need to be in a box which vents outside the car

which your car obviously doesn't have because R33s come with the battery in the boot but not in a box

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328234
Share on other sites

yeah see my problem here is i was taken as part of an 'operation' to an RTA inspection station! this was done at 8pm and i went to this place where thewre was like 20 dudes all sitting around....clearly nothing better to do on a friday night...lol

any my defects were issued by the RTA and then i copped fines from the copper...

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328236
Share on other sites

yes five fines! $81 each!

1. battery not in box or vented to atmosphere

2. ground clearence (by 1mm on resonator of exhaust, car is 110mm high)

3. stealth fx BOV (set to recirculate, but doenst matter)

4. turbo timer

5. rim size (this is bullshit as its all about rolling diametre size and not rim size...tyreplacrd says 17", i have 19")

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328242
Share on other sites

you can fight em in court if you think its worth it

1 is bullshit we know that for sure

2 sounds about right, cause has to be 100mm from the lowest point which seems to be your exhaust

3 gonna have to cop that one

4 turbo timer, i dont know the legality on this

5 you car came stock with 16s AFAIK you have to measure the stock rolling diameter and then measure your current one, is its no more that 15mm more your in the clear.

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328255
Share on other sites

5 you car came stock with 16s AFAIK you have to measure the stock rolling diameter and then measure your current one, is its no more that 15mm more your in the clear.

I thought there was another rule that for the rim that you can only go 25mm wider and 25mm more in diameter. So if your car came with 16x8, then you can go as far as 17x9 (unless you get it engineered of course).

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328432
Share on other sites

Don't you have that plastic thing in the boot which blocks your battery from view? Then put the standard strut brace infront of that as well, your timer is illegal unless wires to hand brake , just relocate it to a more hidden area, I got this single din cover with a flip lid which hides my profec ebc and timer + edfc and never had anyone inspect there

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328702
Share on other sites

one more thing you either got ripped off or the cop was a stupid sod, it should be 81 in total I got defected for 3 things once and the total was $81

Incorrect. You can receive up to 5 infringement notices. Every defect can bedealt with individually

oh and also with regards to the 25mm rim rule in NSW there is no such thing.

This is directly quoted from the RTA

Wheels up to 26mm wider than the largest optional wheel recommended by the vehicle manufacturer for the

vehicle can be fitted without the need to notify the RTA.

The outside diameter of the wheel and tyre combination must be no more than 15mm over the largest diameter

wheel and tyre combination specified for the vehicle and not more than 15mm below the smallest diameter wheel

and tyre combination specified for the vehicle.

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328828
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...