Jump to content
SAU Community

Recommended Posts

I was told that not having mesh over the intercooler is illegal Ricca, I don't have it on mine, but my car is also very sticker worthy, I'm just lucky *crosses fingers*

haha ur a girl you can play with their minds !!

:P

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4330610
Share on other sites

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

Was the guy that you had an Italian looking guy. Slightly short and chubby? that’s the guy i had when i first took my car over, he was picking on stupid little things and he was trying to tell me that he could have my car destroyed if he wanted to which is total crap! Little Hitler. he gets a tiny bit of power and it goes to his head.

Any way i took it back to o’connor again and got tall old bold guy and he was very polite and friendly. it went over fine. took all or 10 seconds of the him to check the car was ok and didn’t even bother to check a few things on my list. He was talking to me about how he liked skylines, the new 35GTR and about ripping skids in his wife’s V8 lol

i don’t think it makes a difference where you go so much as who you get when you go.

Oh and if anyone is having to go over the pits and has a fairly low car i recommend you get in the line for the pit closest to the entrance gate because the edges of the pit are a little lower on that one. All the others have a small drop off in the concrete where as this one does not. My car has just less than 100mm clearance and i was worried about it but went over that one fine. Also don’t go over with too much fuel in the tank because that will drop you down a fair bit.

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4330736
Share on other sites

Damn... this sucks Ricca. I've only ever had one yellow *touches wood* and I went to Welshpool. They were pretty good to me. The guy even gave me this booklet and said, "I see you want to mod your car so here is a booklet of guideline" Couldn't believe it after all the horror stories I'd heard haha

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331035
Share on other sites

I can pretty much guarantee you wont get over with the fibreglass bonnet/guards, unless you know someone. Also i doubt youll find your intercooler is actually cold...... it just cools down the hot air passing through.

1st time i went over the guy didnt care about bonnet / guards he was a good guy he race's V8's or some doodle he only did me due to shockie leak and bold tyers

so i got coilover and fixed everything 2nd time this guys picked on everything (different guy )

Well i will try my luck on wenesday at Whelspool so touch wood it works out!

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331161
Share on other sites

prob will meet you there as i am taking my car over. i am bit worried about my car passing as i just had a RB26 put into it, but heard isnt much prob cause its an opional engine or something like that. does any one know more about this

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331165
Share on other sites

bubba on here got his car past without engineer certs and his engine is a full 1litre increase

i usally go after lunch as thats when everyone is gone and no cars at all haha.

Edited by Flash89
Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331214
Share on other sites

Give midland a go, i passed mine there quick as and i have a cf bonet along with many other mods and the guy commented on it at first then laughed n said i was all good to go. Oh and you have to book your car in @ Midland so you dont need to wait 4 hrs.

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331241
Share on other sites

prob will meet you there as i am taking my car over. i am bit worried about my car passing as i just had a RB26 put into it, but heard isnt much prob cause its an opional engine or something like that. does any one know more about this

Only thing I reckon they might balk at if they're not in the "know" is the "twin" turbo thing (like insurance companies flip out).

Swapping engine as i know need Enginerring cert or complaice plates or something to 100% sure

but yersh might see u their will be going very earily!

Only if it's vastly bigger or different than the original engine.

bubba on here got his car past without engineer certs and his engine is a full 1litre increase

i usally go after lunch as thats when everyone is gone and no cars at all haha.

It was as simple as change the engine number from RB20xxxx to RB30xxxx :D

Give midland a go, i passed mine there quick as and i have a cf bonet along with many other mods and the guy commented on it at first then laughed n said i was all good to go. Oh and you have to book your car in @ Midland so you dont need to wait 4 hrs.

I went to Midland also, booked the earliest available appointment (7:30am I think it was) which might have been the key to getting a nice inspector.. I think there was 3 or 4 lanes and he probably picked my lane as after talking to him, he rather liked skylines and thanked me for driving my car :D

Hmm actually, that was 2nd pass.. now that I think about it I think I got the same guy both times, first pass rego'd the engine and just found some minor stuff like an exhaust hanger off, a split boot had to secure the pod filter and a bit of piping better. Second time over he just checked the items he noted the first time and off came the sticker.

Maybe with the booking system they can utilise the inspectors better so that instead of being so random (and swamped), you get an inspector that knows your type of car..

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331321
Share on other sites

Midland are pretty cool, got my pulsar re-rego'd there.

There is a place in Geraldton that I got my Torana inspected, he pretty much let me do the inspection myself and let me recitify most of the problems there and then, lol.

Link to comment
https://www.sau.com.au/forums/topic/249806-pits/page/2/#findComment-4331379
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
×
×
  • Create New...