Jump to content
SAU Community

Recommended Posts

Mate I sympathise with you being in a small town, been there done that.

My first thought was it sounds like you have an air leak, have you checked right over all your hoses??? Especially the two on the intercooler? They can split under the outter cover and be a royal pain to find.

Can you hear any strange noises? other than the actual engine running poor?

Mate I sympathise with you being in a small town, been there done that.

My first thought was it sounds like you have an air leak, have you checked right over all your hoses??? Especially the two on the intercooler? They can split under the outter cover and be a royal pain to find.

Can you hear any strange noises? other than the actual engine running poor?

Yep checked them all... did the water trick when it's running, just a thought could it be the timing belt has skiped a tooth? making the time way out?

Ok, so no air leaks. But overfuelling still? Next thing to check is the AFM's.

There are two problems with GTR AFM'S as far as I'm aware.

1: The actual loom connector where it plugs onto the AFM. The pins loose their tension causing various, constant or intermitent problems. I had this, took a little while to track down. It would start running rough, smoking etc, so I could pull over, wriggle the connector and you can hear the engine change note.

These connectors are not available from Nissan, some of the SAU supporters sell them. In my case I was working at an importer at the time, Subaru use the same STYLE connector, so I used better condition pins from a subaru connector and joined into the car's loom. Have done over 30,000km with no problem since.

2: The other problem is under the top cover of the AFM there are solder joints where the pins are soldered. With the weight of the connector on them these can fail. There is a thread on SAU showing how to do this. It is quite simple.

Have a look at these two things before stressing yourself out.

Ok, so no air leaks. But overfuelling still? Next thing to check is the AFM's.

There are two problems with GTR AFM'S as far as I'm aware.

1: The actual loom connector where it plugs onto the AFM. The pins loose their tension causing various, constant or intermitent problems. I had this, took a little while to track down. It would start running rough, smoking etc, so I could pull over, wriggle the connector and you can hear the engine change note.

These connectors are not available from Nissan, some of the SAU supporters sell them. In my case I was working at an importer at the time, Subaru use the same STYLE connector, so I used better condition pins from a subaru connector and joined into the car's loom. Have done over 30,000km with no problem since.

2: The other problem is under the top cover of the AFM there are solder joints where the pins are soldered. With the weight of the connector on them these can fail. There is a thread on SAU showing how to do this. It is quite simple.

Have a look at these two things before stressing yourself out

Cheers. can i solder the wires directly to the AFM to test it out? Not wise?

I've actually seen people use individual socket terminals that fit the afm pins then silicon the whole thing up! I personally would never do something like that.

I actually tested mine, I used a couple of paper clips to back probe the afm's with a multimeter when the car was running. My signals were way out of spec, thats what lead me down the afm path.

I cant remember what the specs were and what terminals to test. Its in the workshop manual. I can get it for you tomorrow.

Another thing that can cause similar issues, but it would be constant, is if the fuel pressure reg seized shut, But I'd be checking the AFMs first.

agreed with the self diagnostic check, which is how i knew my AFM were causing an intermitent problem.

do a search and find the link, + a list of the codes.

from memory and this is assuming you have the same single led rear ecu (mines 89')...

remove passenger side kick panel

undo ecu

turn screw on rear of ecu all the way to the right

turn on ignition, wait 2 seconds

turn screw all the way back counter clockwise

the led light on the rear and a light on the dash will flash the code (check with list of codes)

agreed with the self diagnostic check, which is how i knew my AFM were causing an intermitent problem.

do a search and find the link, + a list of the codes.

from memory and this is assuming you have the same single led rear ecu (mines 89')...

remove passenger side kick panel

undo ecu

turn screw on rear of ecu all the way to the right

turn on ignition, wait 2 seconds

turn screw all the way back counter clockwise

the led light on the rear and a light on the dash will flash the code (check with list of codes)

Cheers for that i will try to get to it tonight...

agreed with the self diagnostic check, which is how i knew my AFM were causing an intermitent problem.

do a search and find the link, + a list of the codes.

from memory and this is assuming you have the same single led rear ecu (mines 89')...

remove passenger side kick panel

undo ecu

turn screw on rear of ecu all the way to the right

turn on ignition, wait 2 seconds

turn screw all the way back counter clockwise

the led light on the rear and a light on the dash will flash the code (check with list of codes)

G'day guys. Just wondering if its the same to same on a R32 GTS-t??? Problems with mine.

G'day guys. Just wondering if its the same to same on a R32 GTS-t??? Problems with mine.

UPDATE!

I stripped out the AFM meter to start checking them... as i removed the airbox i notice that the twin turbo pipe was semi loose...

BAM

The twin turbo pipe has a little elbo that sits inbetween the turbo inlet and TT pipe, it had cracked in two and was just sitting on there causing the boost leek and really shit performace. Now to find this part....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...