Jump to content
SAU Community

Recommended Posts

I have just installed a turbo into a GTS and have a few problems I thought you guys could shed some light on. The best way I can describe the problems is when it boosts from about 5psi up it starts to miss, but it only happens in third gear and over, and from about 3000 rpm and up. When the gas is let off the blow off valve does not release the pressure equally, it sort of flutters and the boost gauge jumps up and down rapidly in time with the fluttering. The parts that I got with the turbo are a GTST AAC valve and the o2 sensor. Do I need a GTST afm as well? Any info you guys can provide would be greatly appreciated. Thanks.

Link to comment
https://www.sau.com.au/forums/topic/25025-turbo-problems-rb20de/
Share on other sites

You don't need a GTSt AFM. Make sure you have the DET injectors and make sure you have spark-plugs to suit a GTSt. Remember you make more boost in thrid gear than you do in 1st or 2nd so you should make sure your timing etc is done to accomodate the extra load in the higher gears.

And if anyone tells you that you can't turbo the NA tell them to bite your ass because I did it over a year ago and that car has since been sold twice and is still a rocket.

Running 9~10psi of boost is no problem, I even ran the stock intercooler, it's all in the tuning. I ran the NA computer for a while too as it runs CRAZY rich to keep the engine alive long enough to get it sorted.

Remember there are two ways to turbocharge...

Low compression High Boost

High compression Low Boost

The first is good for top end, the latter for mid range punch, which is why my 32 was so quick on the street.

Tuning, Tuning, Tuning. That's the key.

Little steps at a time.

Well got my car back today unchanged, the guy said its nothing to do with the timing but it looks to be an air/fuel problem. He ran out of time to do anything about it today. On Monday he's going to do tests and stuff with his oscilloscope. I just nodded a said OK as if I knew what he was talking about.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...