Jump to content
SAU Community

Car Detailing Help Me:)

AlexR34

By AlexR34,
in Queensland

 Share

Recommended Posts

AlexR34 Proficient

AlexR34

Posted
Posted

Hi Guys,

Looking for some advice for someone with a bit of experience, when i clean my car and do the wax and yada yada it looks super clean, but when the sun hits it or u look at it under a light there are swirl marks and billions of little scratches (all very light) how would I go about removing these, they crap me of grrrrrr. Looking for specific product names and tools you use, and how can i reduce the swirl marks in the future, what is mainly causing these, is it my sponge, my microfiber towel etc etc.

As usual all help is appreciated in advance.

Thx G's.

Link to comment
https://www.sau.com.au/forums/topic/252282-car-detailing-help-me/
Share on other sites
HKS_R34 Proficient

HKS_R34

Posted
Posted

mainly the scratches can come from the sponge you use when washing the car.

I use mostly all autoglym products as they seem to be the best I have used. The autoglym car wash, follwed with the Ultra Deep Shine, then the super resin polish.

Gets all those scratches and swirls right out.

AlexR34 Proficient

AlexR34

Posted
  • Author
Posted

Im thinking of using the "Ultimate System" from mothers has anybody tried this. What it is is a pre wax cleaner from mothers then followed with a sealer and glaze and finally using their pure carnauba wax. Does anyone have anything to say about any of these products.

AlexR34 Proficient

AlexR34

Posted
  • Author
Posted (edited)

Yeah, im actually gonna clay bar the car first to pick up all the crap and get rid of over spray then im going to do the rest, but whats the easiest way to get rid of swirls and micro scratches. I think ill just get the clay bar system and i think its enough, because you get the clay bar, that instant detailer thing, basically used to moisten the clay bar and a wax and that should do it, but i'd like to get rid of all the swirls and gagilions of little scratches u can see under a bright light. Whats the easiest way to get rid of these scratches.

Edited by AlexR34
Beelzebub89 Grand Master

Beelzebub89

Posted
Posted

Go to Final Inspection and check out the forums there. Plenty of detail about techniques, tools and products to use.

What I do on my cars is:

Wash - Random $15 car wash

Dry with Waffle Weave Microfibre Drying towel

Clay - Clay Magic Blue

Wash Again

Dry again

Polish with Menzerna Intensive Polish (I think its called) and a Bosch Random orbital with a Blue Edge Pad. I've also got Menzerna Final Finish and a White Edge pad if the swirls aren't too bad.

Wax with P21s paste wax

Seal with Zaino Z2

This will normally last a good 6 months before it needs doing again ;) Definetly get onto Final Inspection and order some gear from them. All the products they stock are the best :action-smiley-069:

I use all microfibre clothes on my car and a microfibre wash mit for washing the car. 1 for body n 1 for wheels. This helps minimise scratches from washing the car :D

Enjoy and hope you get your car looking smick :D

Tyson 1990 Community Regular

Tyson 1990

Posted
Posted
mainly the scratches can come from the sponge you use when washing the car.

I use mostly all autoglym products as they seem to be the best I have used. The autoglym car wash, follwed with the Ultra Deep Shine, then the super resin polish.

Gets all those scratches and swirls right out.

I think i use Autoglym polish too, its awesome.

AlexR34 Proficient

AlexR34

Posted
  • Author
Posted
Go to Final Inspection and check out the forums there. Plenty of detail about techniques, tools and products to use.

What I do on my cars is:

Wash - Random $15 car wash

Dry with Waffle Weave Microfibre Drying towel

Clay - Clay Magic Blue

Wash Again

Dry again

Polish with Menzerna Intensive Polish (I think its called) and a Bosch Random orbital with a Blue Edge Pad. I've also got Menzerna Final Finish and a White Edge pad if the swirls aren't too bad.

Wax with P21s paste wax

Seal with Zaino Z2

This will normally last a good 6 months before it needs doing again :( Definetly get onto Final Inspection and order some gear from them. All the products they stock are the best :(

I use all microfibre clothes on my car and a microfibre wash mit for washing the car. 1 for body n 1 for wheels. This helps minimise scratches from washing the car :(

Enjoy and hope you get your car looking smick :D

Yeah ill follow your instructions and ill do all this next week and then ill post pics up of how it looks and what products i used, before you freak out it will be a picture of a 2002 C200 Merc not a skyline i sold that a while ago lol. So yeah next sunday i shall post pics up, the only reason im not gonna get the products that you are recommending is because i can't be stuffed shopping online lol.

O.I.C Napster Collaborator

O.I.C Napster

Posted
Posted

Alex,

I think you'll find the little scratch marks are called spiderwebs. Well thats what we call it. It is caused from either the spounge or cloth you are using to clean the car. IMO your always gonna get them because water will never removed all the dirt before the wash.

When we buff cars, we will clean the car first, leave the car wet and use a cutting compound to cut into the clear coat that will remove those so called marks. The we'll wash the car again, and there is a few different steps we will take to seal the polish and apply the wax.

The wax will fill-in the swirl marks left by hand polishing or machine polishing. You will always get swirl mark no matter how you polish a car. Different products do different jobs.

My advise would be to get a decent cut, to cut into the clear (no to heavy) then apply your final wax/swirl remover to finish.

If your car is a dark colour the marks will stick out like dogs balls but thats just the way it is.

I use a product from 'Autosmart' is not avalible on the retail shelves i dont think but if your up this way drop me a line and ill help u out.

Cheers Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...