Jump to content
SAU Community

Something is wrong =(

BoOsTeD_RB26

By BoOsTeD_RB26,
in Engines & Forced Induction

 Share

Recommended Posts

BoOsTeD_RB26 Experienced

BoOsTeD_RB26

Posted
Posted

Hey all,

Just of last night I have been having some problems with my car. First of all the idle has become really really rough. The car will literally "shake". Im not exactly sure what it is but it seems to be excessively rich as it struggles to stay alive.

I put new plugs in it today but they did absolutely nothing.

Could it be the AFMs?

When the car is like this, the boost gauge also "flickers" while it is in vaccum.

Any ideas?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/25283-something-is-wrong/
Share on other sites
Steve Grand Master

Steve

Posted
Posted

Sounds like it may be a vacuum leak.

The ecu is measuring the air that comes through the AFM, but too much air gets in, so the ecu compensates by adding more fuel as it tries to maintain idle, then it over fuels, cuts the fuel - viscious cycle.

If it is vacuum, you will notice it alot more when hot than when cold too.

My guess anyways:)

have you checked all your vacuum lines?

MRK25T Experienced

MRK25T

Posted
Posted

I may have similar problems with my car.

When I stop up a hill (this occurs when driving normaly beforehand) the revs drop really low (sometimes at this point the car stalls) and then pick themselves. This loops for about 5 seconds (at a frequenct of about 1 cycle per .5sec) and then the revs stabalize.

Background:

I have a s2 R33 gtst.

I have a blitz BOV.

My AFM maxes out at less than 250rwhp on the dyno.

Sometimes when going up a hill at about 4000rpm by engine check light flashes (indicating my AFM is maxing out - its not the quick flashing that indicates pinging).

I'm running low boost (0.6bar) when this happens.

There is a Z32AFM sitting under my bed waiting to be installed to fix my AFM problems.

Anyone know what my problem is?

Mark

Steve Grand Master

Steve

Posted
Posted

Well I am not sure if this is the prob, but does the pump have a non return vavle fitted? I have seen the non return valve taken off the top of 044 pumps to make them easier to connect.

I am sort of guessing :P, but when at idle the fuel pump will switch on and off as fuel pressure increases and decreases, just like when you turn the ignition on and dont start the car, the pump will prime then shut down. I am thinking that perhaps the pump is shutting down, and fuel may be returning back down the lines, which isnt a major problem until you are facing up a hill.

Have a look at boostmeisters low engine rpm stalling thread, goes into detail of wiring fuel pumps to be constantly on to avoid such dramas. Not sure if this is your prob, but may be:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Got my 34 gtt tuned last week. Car made 362 wheel horsepower at 19 psi. Turbo was the ATR43SS. Only other upgrades were haltech 2000 series. 650cc injectors, walbro 250, fmic. Pro hub dyno reads 6% lower than actual figure according to my tuner. Car is a real ripper now.  IMG_7261.mov
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Hi everyone, I'm wondering if anyone in Melbourne (preferably West) has a non-S2 R34 front bar. If it's already off the car, even better!  Nothing too weird, I just need to get a cut-out of the hole that the front indicators clip into 🤣 (image attached for reference)   I've got a front bar from JSAI Aero, but those holes need to be cut myself, and I want to get it right so the indicators will clip securely. And my OEM bumper is a S2, so I have no reference. So looking for a member who might be able to spare me a few minutes to make a cardboard cut-out using your front bar.
×
×
  • Create New...