Jump to content
SAU Community

Recommended Posts

Hey all,

Just of last night I have been having some problems with my car. First of all the idle has become really really rough. The car will literally "shake". Im not exactly sure what it is but it seems to be excessively rich as it struggles to stay alive.

I put new plugs in it today but they did absolutely nothing.

Could it be the AFMs?

When the car is like this, the boost gauge also "flickers" while it is in vaccum.

Any ideas?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/25283-something-is-wrong/
Share on other sites

Sounds like it may be a vacuum leak.

The ecu is measuring the air that comes through the AFM, but too much air gets in, so the ecu compensates by adding more fuel as it tries to maintain idle, then it over fuels, cuts the fuel - viscious cycle.

If it is vacuum, you will notice it alot more when hot than when cold too.

My guess anyways:)

have you checked all your vacuum lines?

I may have similar problems with my car.

When I stop up a hill (this occurs when driving normaly beforehand) the revs drop really low (sometimes at this point the car stalls) and then pick themselves. This loops for about 5 seconds (at a frequenct of about 1 cycle per .5sec) and then the revs stabalize.

Background:

I have a s2 R33 gtst.

I have a blitz BOV.

My AFM maxes out at less than 250rwhp on the dyno.

Sometimes when going up a hill at about 4000rpm by engine check light flashes (indicating my AFM is maxing out - its not the quick flashing that indicates pinging).

I'm running low boost (0.6bar) when this happens.

There is a Z32AFM sitting under my bed waiting to be installed to fix my AFM problems.

Anyone know what my problem is?

Mark

Well I am not sure if this is the prob, but does the pump have a non return vavle fitted? I have seen the non return valve taken off the top of 044 pumps to make them easier to connect.

I am sort of guessing :P, but when at idle the fuel pump will switch on and off as fuel pressure increases and decreases, just like when you turn the ignition on and dont start the car, the pump will prime then shut down. I am thinking that perhaps the pump is shutting down, and fuel may be returning back down the lines, which isnt a major problem until you are facing up a hill.

Have a look at boostmeisters low engine rpm stalling thread, goes into detail of wiring fuel pumps to be constantly on to avoid such dramas. Not sure if this is your prob, but may be:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...