Jump to content
SAU Community

Recommended Posts

Hey, ive been busy with my car and all the internals are done, but before it drives i need to change every oil in the car. I have the manual but left it at a workshop and wont be able to get it till 28th of January. Wondering if we can get a list of oil levels for my r33 gts-4

Engine: 5.3 Liters (gts-4)

Gearbox: 4.1 Liters

(thats the only solid and sure information i have on oils for my car)

Transfer case:???

Diffrential's:???? (also is the rear bottle in the boot for the rear Dif?"Atessa actuator"

Power steering:????

Clutch and brakes i have experience with and there about 500ml's each. Its just those three i need before i go out and but the tiny redline bottles because a gallon is awkward and i suspect i need to get a quart bottle ;)

Please help as ive looked for those three and its all different.

Cheers, Andrew

Link to comment
https://www.sau.com.au/forums/topic/252970-list-of-oil-levels/
Share on other sites

nar i got the engine and gearbox oil from the cars manual along with all r33 engines

RB20E: 4.8

RB25DE: (2WD) 4.8

(4WD) 5.3

RB25DET: 5.0

RB26DETT: (STD) : 5.1

(N1) : 6.4

NOTE* this is when the engine is (over-haul) so it can have no possible remaining oil and the oil filter need 400ml as its empty. same or gearbox i got it from the book so this is why i trust that info.

im 99% sure the transfer case is 1.8Liters but didnt want to say anything.

  • 8 months later...

hey guys just serviced my gearbox and diff on my 33 gtst series2... gearbox took roughly 3.5 litres and the diff took 1.7 the weird thing is that some manuals where saying the gearbox takes 2.5 litres and others saying 3.5... i tried it out with 2.5 litres and then with 3.5 litres and i have to say it felt better with 3.5 litres if some one could correct me in regards to this it would be helpfull, cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...